After reboot my SATA 1TB WD1000FYPS (previously is was "Drive error") is marked 0 mb in 3ware web gui.
Available Drives (Controller ID 0) Port 1 WDC WD1000FYPS-01ZKB0 0.00 MB NOT SUPPORTED [Remove Drive]
SMART gives me only Device Model and ATA protocol version 1 (not 7-8 as it must be for SATA)
What does it mean?
Just before reboot, when is was marked only with "Device Error", smart was:
Device Model: WDC WD1000FYPS-01ZKB0 Serial Number: WD-WCASJ1130*** Firmware Version: 02.01B01 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Mar 7 18:47:35 2010 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled SMART overall-health self-assessment test result: PASSED SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 188 186 021 Pre-fail Always - 7591 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 229 5 Reallocated_Sector_Ct 0x0033 199 199 140 Pre-fail Always - 3 7 Seek_Error_Rate 0x000e 193 193 000 Old_age Always - 125 9 Power_On_Hours 0x0032 078 078 000 Old_age Always - 16615 10 Spin_Retry_Count 0x0012 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0012 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 77 192 Power-Off_Retract_Count 0x0032 198 198 000 Old_age Always - 1564 193 Load_Cycle_Count 0x0032 146 146 000 Old_age Always - 164824 194 Temperature_Celsius 0x0022 117 100 000 Old_age Always - 35 196 Reallocated_Event_Count 0x0032 199 199 000 Old_age Always - 1 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
What can be wrong with he? Can it be restored?
new smart is
=== START OF INFORMATION SECTION === Device Model: WDC WD1000FYPS-01ZKB0 Serial Number: [No Information Found] Firmware Version: [No Information Found] Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 1 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Mar 8 00:29:44 2010 MSK SMART is only available in ATA Version 3 Revision 3 or greater. We will try to proceed in spite of this. SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported. Checking for SMART support by trying SMART ENABLE command. Command failed, ata.status=(0x00), ata.command=(0x51), ata.flags=(0x01) Error SMART Enable failed: Input/output error SMART ENABLE failed - this establishes that this device lacks SMART functionality. A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
PPS There was a rapid grow of " 192 Power-Off_Retract_Count " before dying. The hard was used in raid, with several hards from the same fabric packaging box (close id's). The hard drives were placed identically. Rapid means almost linear grow from 300 to 1700 in 6-7 hours. Maximal temperature was 41C. (thanks to munin's smart monitoring)
On the harddrive's PCB (on bottom) I have found contact pads with unusual colors. The most pads (not soldered) are Yellow, but some are blue and some are somewhere between orange and red. The max temperature for the drive was 42-43 Celsius. The 2 drives, which was next to the died one is normal, all unsoldered pads are yellow.
The harddrive was used for 2 years in RAID with rather big load.