Take the 2-minute tour ×
Super User is a question and answer site for computer enthusiasts and power users. It's 100% free, no registration required.

I want to know about the method with which we can calculate data transfer speed.

If I am sending a 1 GB file through a 1 Gb/s LAN connection, from one computer to another, how much time will it take to transfer that file?

share|improve this question
2  
Have you ever noticed how the windows File Copy dialog say 1 min, then 10 seconds, then 8 minutes, then 14 seconds ? That should give you an idea as to how hard doing this correctly is. –  Toby Allen Jul 10 '12 at 20:38
add comment

5 Answers

As Hippo and MaQleod have stated a byte is 8 bits.
This means 1Gigabit = 0.125 GigaBytes = 125 MegaBytes.

This means the theoretical maximum of a 1Gbps connection is 0.125 GigaBytes per second.

Remember, the entire connection will run at the speed of the slowest element. So, if you're downloading to your hard drive you'd expect it to be limited to the speed of the drives - about 60-70MB/s for a common mechanical hard drive.

Chances are even if there's nothing else to limit the speed you will still not achieve the theoretical maximum speed for data transfer because of other restricting factors such as packet overhead.

Also, you ideally want to make sure you are using Cat6 cabling, not Cat5/5e


Note on size prefixes

This section is why I felt I'd add my answer, even though it's a moderate dupe of the answers so far.

There are two main schemes for prefixing bytes to indicate magitude:

SI Prefix (abbr)= Num Bytes             |  IEC Prefix (abbr)= Num Bytes       
-------------------------------------------------------------------------------
1 GigaByte (GB) = 1 000 000 000 (10^9)  |  1 GibiByte (GiB) = 1 073 741 824 (2^30)
1 MegaByte (MB) = 1 000 000     (10^6)  |  1 MebiByte (MiB) = 1 048 576     (2^20)
1 KiloByte (KB) = 1 000         (10^3)  |  1 KibiByte (KiB) = 1 024         (2^10)

It is highly common for most people to use the SI prefix to mean the IEC number of bytes, although in all "offical" terms this usage is deprecated and shouldn't be used. It doesn't help that both prefix patterns are often incorrectly represented by the same short versions - you often can't tell just by looking if GB is GigaByte or GibiByte, even though it should be Giga, it's often used to represent Gibi - such as in Windows Explorer for example.

This is why you often buy a 500GB hard drive that, when connected, only has ~465GiB of space - the manufacturer is using Giga, and the OS is using Gibi.

In terms of GigaBit Ethernet, it runs at a speed of 1000 Megabits per second - or 1 000 000 000 bits/s - so for completeness the final results are:

1 Gigabit  =  125 000 000 Bytes  =   125 MegaBytes  =   0.125 GigaBytes 
                                 =  ~119 MebiBytes  =  ~0.116 Gibibytes  
share|improve this answer
    
The IEC prefixes are not shorted like the SI ones: Gibibyte is shorted to GiB. Also, all telecommunication speeds are fully in SI scheme, and it is not uncommon for hard drive manufactures to mark a 1000 GiB hard drive as 1 T(i)B one (the GiB is real, and TiB is imaginary here). –  whitequark Nov 29 '10 at 15:05
    
@white you are correct, thanks, I'll see about fixing it. I'm starting to think I should leave old posts alone even in the face of an error, there's also something else that crops up to change after the initial one. ;) –  DMA57361 Nov 29 '10 at 18:59
    
In my experience, the size of the file doesn't matter as much as the protocol involved. NFS has much higher transfer speeds than SMB due to the packet overhead. There is much more information being sent over SMB than there is with NFS. So the calculation really is moot if you don't account for the protocol. –  MaQleod Jul 10 '12 at 20:36
add comment

In a 1 Gbps connection, 1 Gigabit will take 1 second. Since there are 8 bits in a byte, 1 Gigabyte will take 8 times longer.

So your 1 GB file will take 8 seconds in ideal conditions. However, hard disk speeds are usually much slower, so your file transfer might take three times longer to complete.

share|improve this answer
add comment

1 byte = 8 bits, this means that 1 gigabyte is equal to 8589934592 bits, or 8 gigabits. So 1 gigabyte will take 8 seconds on a 1 gigabit/second LAN (but you have to allow for some packet overhead and so it will take a bit longer).

I must add that this will vary GREATLY depending on protocol. For instance, transfers over NFS have much lower overhead that packets over SMB and both are significantly faster/leaner than NETBIOS (which hopefully no one in their right mind is using anymore).

share|improve this answer
add comment

The transfer protocol matters. I am assuming you are using Windows since it is the most common OS. Also the lack of details on your question implies that you are using the "Windows File Sharing" which uses SMB. I would say that you'll see 20-30 Megabytes per second. That is, again, assuming all the computers are running on Windows 7 or at least Vista SP1, and Gigabit ethernet connected correctly.

I suggest you to get teracopy or something similar and watch the copy speed and get a better estimate.

share|improve this answer
add comment

Note that: The 1GB file = 1 x 2^30 bytes = 2^33 bits. (on Windows OS as it incorrectly uses SI prefix when they should be using IEC instead.. [1])

While the data transfer rate: 1Gb/s = 10^9bps.[2]

So "ideally" it would take...

2^33 bits / 10^9bps = (8,589,934,592)b / (10^9)bps = ~8.58s

Ofcourse, the HDD latency, network parameters, propagation delay, etc.. play a part in the final estimation.


Reference:

  1. http://en.wikipedia.org/wiki/Data_rate_units#Problematic_variations
  2. http://en.wikipedia.org/wiki/Data_rate_units#Conversion_formula
share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.