Take the 2-minute tour ×
Super User is a question and answer site for computer enthusiasts and power users. It's 100% free, no registration required.

Note:

DNS:

Wireless NIC:

Intel Corporation PRO/Wireless 3945ABG

Kernel module:

iwl3945

uname -r

2.6.28-11-generic

Release:

Distributor ID: LinuxMint
Description:    Linux Mint 7 Gloria - Main Edition
Release:    7
Codename:   Gloria

ip a | grep inet6:

inet6 ::1/128 scope host 
inet6 fe80::21b:38ff:fe0c:d718/64 scope link

tail /etc/modprobe.d/blacklist.conf

# blacklist ipv6
blacklist ipv6

Question

  • How to improve the connection speed, to match with (or similar) to Ethernet or Win NT 5.1 wireless driver?
share|improve this question
add comment

3 Answers

up vote 3 down vote accepted

Your wireless card is 802.11a/b/g, which has a max physical layer throughput of 54 Mbit/sec. This maximum is rarely achieved in 'normal operating conditions' for most people, and you're more likely to see much slower speeds. Compared to a typical 100 Mbit ethernet card which has a max physical layer throughput of ... 100 Mbit, you should not expect to reach the same level of performance.

What you gain in mobility and convenience with Wireless is supposed to outweigh the speed/performance benefits of being tied down with ethernet. Bondage puns unintended, but channel bonding puns implied.

Fwiw, IPv6 is not primarily intended to provide performance gains, it's main benefit is increased address availability. Disabling it may or may not affect performance.

There's a myriad of reasons for differences in Windows vs Linux drivers, not least of which is whether the vendor contributed the driver to Linux. You may be able to tune kernel network parameters with sysctl, or by manipulating the driver module load options. Finally, the driver from Windows may load on Linux using NDISwrapper.

For more information on sysctl:

  • On Ubuntu and Debian systems the file /usr/share/doc/procps/examples/sysctl.conf is heavily commented.
  • The man pages for sysctl and sysctl.conf may be helpful.
  • Some performance settings on Ubuntu with sysctl.

There seems to be more information about sysctl on Linux 2.4 kernels than 2.6. I'd have to go delving into the Linux source code documentation for more.

share|improve this answer
    
Thanks for your reply. I understand this. However, on Win NT 5.1, the throughput is much greater compared to Linux (as per above). I suspect disabling IPv6 to improve performance? –  Aaron Aug 10 '09 at 22:56
    
Do you know where I can find sysctl "network parameters" references (to that of sysctl -a? –  Aaron Aug 11 '09 at 17:00
add comment

If your Access Point has another device on it that can only do B speeds, then it's possible that it's stepping down all of its clients, including your g card.

Might want to enforce g on the AP if that's an option.

share|improve this answer
2  
+1 This is an excellent suggestion! –  Axxmasterr Aug 10 '09 at 23:05
    
I don't understand. What is an "AP"? –  Aaron Aug 10 '09 at 23:09
    
@Aaron: AP = access point. Yours may be integrated as part of a wireless router. –  derobert Aug 10 '09 at 23:12
add comment

I would recommend doing a site survey of the electromagnetic spectrum. If someone is using the same frequencies that would explain the performance issues you are having. I discussed an issue similar to this in another thread. Here is the answer I gave to a similar question.

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.