Take the 2-minute tour ×
Super User is a question and answer site for computer enthusiasts and power users. It's 100% free, no registration required.

I read somewhere that smaller (in terms of disk space) hard drives are faster than equivalent but bigger hard drives. How true is this? In other words, say I have two hard drives. Both are of the exact same brand and specs, but one is an 80GB while the other is 500GB. Which would be faster? Or does storage capacity not have any effect on speed at all?

share|improve this question
I am not able to understand the kind of confusion of ideas that caused you to ask this question. Perhaps you can enlighten me as to why you thought this? –  waiwai933 Aug 30 '09 at 7:55
Well I have two almost-identical hard drives; a 500GB and an 80GB. Their specs are almost exactly the same, and I recently had to install an operating system on each, and it seemed like the 80GB one was slightly faster (mainly booting up). I was just wondering if the storage capacity had anything to do with it, or whether it was something completely unrelated. –  Sasha Chedygov Aug 30 '09 at 8:07
benchmark the drives with HD tune. on their website you'll also find an extensive result browser to compare your results against other drives of the same model. –  Molly7244 Feb 3 '10 at 0:48
I had a 160 GB Seagate HD with Win 7, and then I upgraded to a Seagate 500 GB HD. The smaller hard drive was much faster than the 500 GB. I was surprised and a little disappointed. Both hard drives were brand new. I only switched them because I wanted to put the smaller one in a different computer. –  user295574 Feb 2 '14 at 20:24

7 Answers 7

up vote 16 down vote accepted

A generalisation isn't useful, but mostly when talking similar models/same series I'd say the larger drive would be faster due to higher data density in some way (be it more platters and heads, or just denser platters).

The bigger model would likely be newer as well and could benefit from firmware and other production improvements.

share|improve this answer

A hdd has a few platters. If both 80g and 500g has the same number of platters. That would mean the OS installed would fall in several platters on the 80G where as 1 or 2 platter on the 500G.

Each platter would have its own read and write. So on the 80G it is serviced by more heads than the 500G. So it is faster.

share|improve this answer

In general I agree everyone else's answers. Given two hard drives with all else being equal the drive with greater data density will outperform the one with lower data density.

I can think of two scenarios where a larger drive capacity is a detriment to performance. In both cases it is not the drive that's the bottleneck but the file system.

  • Formatting the drive

This is simply a matter of common sense. Since formating touches every byte on a drive a larger drive capacity will take longer to format. Since this is usually only done during an OS installation its not really a problem. In most cases its unnecessary to perform a full format operation anyway.

  • Bumping into the limitations of the file system in-use

The best example of this was the point when drive capacities started to push the limits of the FAT file system. Without getting too technical FAT was designed for disk capacities a fraction of the size of its theoretical limits. FAT16's limit was around 2GB but as partitions approached this limit not only did they waste significant amounts of space but the overall performance of the file system degraded. FAT32 broke the 2GB barrier and performed better than FAT16 but ran into the same problem when drive capacities started approaching its theoretical limit (its around 2TB but this would be laughable to even attempt)

Each file system has different best and worst case running conditions. Modern file systems are designed to at least maintain performance if not improve it as drive capacity grows at the expense under-performing on small drives. A reasonable trade-off considering drive capacities are continuing to grow.

share|improve this answer

If your question were about the physical size of the drives, then yes - a 2.5" 7200 rpm drive is faster than a 3.5" 7200 rpm drive of the same size. The read-write heads do not needs to move as far.

share|improve this answer
No I was asking about storage capacity, but good to know, thanks. –  Sasha Chedygov Aug 30 '09 at 4:56
A 2.5" HDD will typically have a smaller, slower and more-precise head actuator (aka voice coil) compared to a similar class of 3.5" HDD. The result is that they tend to have very similar seek times despite the differences in platter size. –  sawdust Jun 15 '11 at 1:25

Size is but one of numerous considerations in determining the actual realized performance of a drive.

Rotational speed is one of the factors that determines the write rate. A 15k RPM drive would likely be faster than a 10K RPM drive of the same specs and size. (Assuming all things are equal which they are not in most cases)

The next thing to consider is the expediency in which the voice coil can move the read/write heads for a seek or continued file access. The latency introduced by the moving voice coil read/write head is perhaps the most significant source of delays in the read/write process.

The electronic controller board and what connectivity BUS it supports is also another significant determination of speed. A good example is the various versions of SCSI disks which supported higher and higher speeds with every revision to the scsi standard. SAS drives offer aditional performance over SCSI,IDE and SATA because of increased BUS bandwidth.

The number of platters is indeed also a factor but not the most critical performance consideration.

share|improve this answer
Great overview, and I'd vote you up, but you didn't actually answer my question. All else equal, would a 80GB or a 500GB be faster? I know about rotational speed and seek latency, I was just wondering if the size of the drive played a part in performance. –  Sasha Chedygov Aug 12 '09 at 7:08
Under most circumstances the 500 GB drive would be faster. –  Axxmasterr Aug 12 '09 at 10:53


High data density is desirable, as it has a positive impact on data transfer performance: the more bits the drive can read concurrently, the faster it is. As a result, a new 3.5" 7,200 RPM hard drive always outperforms an older model. However, access time doesn't benefit from higher storage densities, as the head positioning cannot possibly be accelerated without putting substantial mechanical strain on the components.

share|improve this answer
The use of the word "concurrently" in regards to reading the data is misleading, if not inaccurate. Only one R/W head is active at a time, and the data stream is bit serial. –  sawdust Jun 15 '11 at 1:38

You can not. Drive speed depends on lot of things, mostly on disk data density (is rotational speed is equal).

If you can, between two disks with same capacity, use one with lower number of platters.

share|improve this answer
Doesn't a lower number of platters also correspond to a lower number of read/write heads connected to the voice coil? –  Axxmasterr Aug 11 '09 at 22:25
I would presume that that means that the head actuator can move faster in positioning the head, as well as improving spinup/spindown times. –  RCIX Aug 11 '09 at 22:50
um... "voice coil"? Aren't we talking about Hard Drives, not speakers? –  Chris Pietschmann Aug 11 '09 at 23:50
Unfortunately, some have erroneously extended this idea that a lower number of platters and R/W heads always benefits performance. –  sawdust Jun 15 '11 at 1:53
In servers and RAID configurations more platters means more performance, because the read/write jobs can be split into pieces and done concurrently across many heads and platters at once. (I know the Q is about single drives and desktops, I just wanted to head off the "lower platters == better" meme before it got too far) –  matt wilkie Jun 11 '14 at 17:28

Your Answer


By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.