Super User is a question and answer site for computer enthusiasts and power users. Join them; it only takes a minute:

Sign up
Here's how it works:
  1. Anybody can ask a question
  2. Anybody can answer
  3. The best answers are voted up and rise to the top

I just bought a D-Link DIR-655 router, and I've noticed a significant difference between the wired and wireless speeds when browsing the internet. My cable connection is supposed to have a speed of 20 Mbps, but I noticed today that I can only get about 11 Mbps over a wireless connection. Running the same test (using, I found that I could hit just over 20 Mbps using a wired connection, so the internet connection isn't the problem.

I've tried adjusting the channel to Channel 11 (rather than letting the router choose - it was on Channel 1 to begin) after looking at the other channels in use in this area. I even tried disabling the encryption (WPA2) to see if that would help, but it didn't. The wireless card in my four year old laptop can't do 802.11n, so the router is set to connect on G only.

The Dell utility that came with the driver for the wireless card (built-in, not external) on my laptop shows no significant noise on the connection. Windows (XP, SP3) is showing the connection has 'Excellent' signal strength and the speed there is reading as 54.0 Mbps as is normal for a G connection.

I'm not sure what else could be disrupting the signal. The router is unfortunately right next to a speaker, and there is a cordless telephone in the room, but I would have expected that these devices would show up as noise in the utility if they were a problem. My assumption is that the problem is with the router itself, but I am unable to determine how to confirm/correct this.

Any suggestions would be much appreciated.

share|improve this question

Usually on G wifi, from my experience the real speed is around 12 mbits. Here is a table with theoretical speeds:

  • 802.11b - 11 Mbps (2.4GHz)
  • 802.11a - 54 Mbps (5 GHz)
  • 802.11g - 54 Mbps (2.4GHz)
  • 802.11n - 600 Mbps (2.4GHz and 5 GHz) - 150Mbps typical for network adapters, 300Mbps, 450Mbps, and 600Mbps speeds when bonding channels with some routers
  • 802.11ac - 1300 Mbps (5 GHz) - new standard that uses wider channels, QAM and spatial streams for higher throughput

Below is a breakdown of actual real-life average speeds you can expect from wireless routers within a reasonable distance, with low interference and small number of simultaneous clients:

  • 802.11b - 2-3 Mbps downstream, up to 5-6 Mbps with some vendor-specific extensions.
  • 802.11g - ~20 Mbps downstream
  • 802.11n - 40-50 Mbps typical, varying greatly depending on configuration, whether it is mixed or N-only network, the number of bonded channels, etc. Specifying a channel, and using 40MHz channels can help achieve 70-80Mbps with some newer routers. Up to 100 Mbps achievable with more expensive commercial equipment with 8x8 arrays, gigabit ports, etc. 802.11ac - 70-100 Mbps


Right now, I've 802.11n network @ home, but even the router and my PC says it's connected @ 300 mbit, I can get only about 20 mbits real speed through a wall.

The Wifi "standart" speeds are not achievable in typical conditions, it sounds to me more like marketing speed.

share|improve this answer

Check out You can monitor different signals that could be causing interference with both channels 1 and 11. It may help you find the best channel to use. Also if your router has autoswitching enabled for the 20 and 40MHz, try to disable that to the proper frequency your adapter uses to connect. This can sometimes help get a bit of extra juice.

share|improve this answer
Thanks for this. I tried the program and found a clear channel (the program is currently reporting mine as the only device on that channel), but there was no improvement in speed (at least not from Channel width only seems to apply to 802.11n, and the setting doesn't even appear on the config page when the router is set to use G only, as mine is. Thanks anyway. – AgentConundrum Jul 8 '11 at 2:25

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .