I am talking about this:
What should I set in minimum and maximum? I want good CPU performance but not overheated CPU and fan working like crazy.
These settings determine the range of performance states (or P-states) that Windows will use. In effect, this will vary the processor's clock speed and, if supported, voltage and FSB speed - increase them to meet the workload requirements, or decrease them to reduce power consumption and heat output.
To elaborate, most processors support a number of P-states, which are a combination of a frequency multiplier (also known as frequency ID or FID) and supply voltage (voltage ID or VID). A processor's clock speed is the product of FSB speed multiplied with the FID, so by choosing a lower multiplier, the clock speed can also be lowered. Some processors1 are also able to cut the FSB speed in half, resulting in what's known as SuperLFM (Super Low-Frequency Mode).
The number of P-states supported varies by processor, but is usually around 5-10. Since Windows allows a total of 100 different values for the processor state, this means that not every value will result in a different P-state being used. In other words, going from 100% to 99% or even 90% might have no effect whatsoever on the clock speed. Also, depending on which P-states are supported, the actual clock speed might differ considerably from what you might expect from the percentage; specifying 50% in Windows power options doesn't necessarily mean that your processor will run at 50% clock speed. For instance, on my Core 2 Duo T9550 with a nominal clock speed of 2.66 GHz, setting the processor state to 50% doesn't give a clock speed of 1.33 GHz, as might be expected. Instead, Windows chooses the lowest supported multiplier (FID 6), which results in a clock speed of ~1.6 GHz (FSB 266 MHz × multiplier 6 = 1596 MHz), or 60% of the nominal clock speed, as evidenced by the image below.2
Also, even if the minimum state is set to 1%, my processor won't go below ~800 MHz (SuperLFM), which is the lowest supported clock speed (FSB 133 MHz × multiplier 6 = 798 MHz); this is 30% of the nominal clock speed.
According to the documentation available here:
Intelligently choosing the percentages for Windows power options, then, involves finding out which P-states your processor supports, deciding the minimum and maximum clock speeds you wish to use and then entering the percentages that result in those clock speeds. There's no single correct answer as everything depends on your goals - whether you want to maximise performance or battery life, reduce temperatures or something else entirely. Experiment and see what works out best for you. Personally I've found that setting minimum and maximum to 5% (low enough to force lowest multiplier regardless of processor) and 100%, respectively, gives the best results. Yes, even on battery. While it might seem logical to set maximum processor state to less than 100% on battery, in my experience it's better to have the processor spend some time in the highest P-state and then return to idle as fast as possible, than to have it spend more time in some intermediate state.
For advanced tweaking, utilities like RMClock allow you to disable some P-states, as well as overclock and under- or overvolt your processor. While I personally haven't tried it, I've seen recommendations to only have two P-states enabled - the lowest possible multiplier (SuperLFM if supported) for idling, and the highest possible multiplier (at the lowest stable voltage) for everything else. Certainly something to consider playing around with if interested in such things. As long as you don't overclock or overvolt, the worst-case scenario is a BSOD and a restart.
1 For instance Intel Core 2 Duos, but not, I believe, newer Core i-series processors.
Minimum and Maximum processor state is the percentage of CPU speed of which it will run at.
For Example, you have a CPU at 3.00Ghz, then
If you set the Minimum Processor state to 10% and maximum to 90% then your processor speed will vary from 0.3Ghz (10% of 3.00Ghz) and 2.7Ghz (90% of 3.00Ghz).
Lowering these would of course decrease performance under heavy workload. This is same kind of question like using a high speed CPU (3.00Ghz+) or a low speed CPU (~1.5Ghz) and number of cores matter.
For you are asking for Optimal settings then it would be:
And if you want the best performace all the time (at the cost of battery while on battery) then
And for the OverHeating topic, processor would not overheat (it will heat up tough) until you stress it, running heavy software like some heavy games can overheat it, it also depends on which processor and cooling system you are using, i would be able to help you more if you specify some more info
Actually it is a completely different topic.
If you want more info read these:
Hoping this helps..
EDIT: Each CPU has a number of Processor State, We can not set the CPU other than these CPU states. I took those values just for example.
To address the specific title question. I think the state that these settings refer to is also known as P-State.
Meaning, it's a control over the peak CPU frequency (and as the link explains, also the voltage used).
There is also a more technical documentation of the implementation of the power saving techniques implemented in the Vista line of Windows operating systems.
To my understanding, this is where you can see the currently set maximum CPU frequency of the system:
These minimum and maximum refer to the minimum and maximum cpu power available. If you set the maximum processor state in Power Management to 50% it should offer up to 50% of its processing power when put under load.
Windows 7 is able to vary the processor clock frequency according to the processor usage. Minimum and maximum processor state control the range within which Windows varies the clock speed.
For example, assume that your CPU is capable of 0 to 2.4 GHz, meaning that your maximum processor speed is 2.4 GHz. A minimum of 25% and a maximum of 75% will make Windows vary the speed between 600 MHz (25%) and 1.8 GHz (75%) out of the 2.4 GHz processor. "On battery" and "plugged in" is for setting two different ranges for the discharging and charging states.
The point of reducing clock frequency is that, the higher the frequency, the more heat the processor will produce, and the more power it will consume. The lower the frequency, the more time it will take to complete processing (calculating).
The article How To Prevent Your Laptop From Overheating reports this :
Its simple. For minimum set about 5%, for maximum set 100%. You get all power you need, but when is CPU idle, it goes to lowest possible frequency. Dont worry about 5%,CPU newer can go so low. In my case (core2duo@3,2GHz) lower state is 2GHz even I set minimum to 5%.
Actually, all the people are answering from theory and books. I personally tried setting the maximum processor state at 30% and gain only 1 degree Celsius in overheat. I undervolted the processor to the minimum of getting a BSOD in 5 minutes of stress, and gained another 1 degree Celsius.
I stress the fact that the laptop, a Lenovo E540, is new, with cleaned exhaust channels, clean fan, new Thermal paste (best and most expensive on the market - about 25$ in a very tiny bottle). All this effort for only 2 degrees Celsius. This is because it's kind of a cheap laptop for Lenovo, not in the T or W series. The heatsink is very poor, and nothing on Earth can cope with that. The processor likes to stay at around 50-52C when idle, and 70-75C at load. These figures are with the above tweaks and without.