Take the 2-minute tour ×
Super User is a question and answer site for computer enthusiasts and power users. It's 100% free, no registration required.

I have a several large files on optical media I would like to copy to multiple targets - in this case I have two hard drives attached to the same computer. Is there a utility that can function like:

copy source target1 target2 ... targetN
share|improve this question

7 Answers 7

up vote 16 down vote accepted

For single files you can use tee to copy to multiple places:

cat <inputfile> | tee <outfile1> <outfile2> > <outfile3>

or if you prefer the demoggified version:

tee <outfile1> <outfile2> > <outfile3> < <inputfile>

Note that as Dennis points out in the comments tee outputs to stdout as well as the listed files, hence using redirect to point to file 3 in the above examples. You could also redirect this to /dev/null as below - this has the advantage of keeping the file list more consistent on the command line (which may make it easier to script up a solution for variable numbers of files) but is a little less efficient (though the efficiency difference is small: about the same as the difference between using the cat version or the version without cat):

cat <inputfile> | tee <outfile1> <outfile2> <outfile3> > /dev/null

You could probably combine one of the above with find quite easily to operate on multiple files in one directory and less easily to operate on files spread over a directory structure. Otherwise you might just have to set the multiple copy operations off in parallel as separate tasks and hope that the OS disk cache is bright and/or big enough that each of the parallel tasks used cached read data from the first instead of causing drive-head thrashing.

Edit: tee is commonly available on standard Linux setups and other unix or unix-alike systems, usually as part of the GNU "coreutils" package. If you are using Windows (your question doesn't specify) then you should find it in the various Windows ports such as Cygwin.

share|improve this answer
    
I found tee.exe to be part of the UnxUtils package. Thanks for the great tip! –  Goyuix Aug 31 '09 at 14:40
5  
Note that tee will also output to stdout, so you may want to do tee outputfile1 outputfile2 < inputfile > /dev/null since outputting a binary file to the terminal could be noisy and mess with its settings. –  Dennis Williamson Oct 26 '10 at 20:24

Based off of the answer given for a similar question Another way is to use GNU Parallel to run multiple cp instances at once:

parallel -j 0 -N 1 cp file1 ::: Destination1 Destination2 Destination3

The above command will copy file1 to all three destination folders in parallel

share|improve this answer
    
Very cool. I hadn't seen GNU parallel before. Thanks! I wonder how it performs when the destinations are dramatically different speeds. –  Goyuix Jul 1 at 21:34

For Windows:

n2ncopy will do this:

alt text

For Linux:

The cp command alone can copy from multiple sources but unfortunately not multiple destinations. You will need to run it multiple times in a loop of some sort. You can use a loop like so and place all directory names in a file:

OLDIFS=$IFS
IFS=$'\n'

for line in $(cat file.txt):
do
   cp file $line
done

IFS=$OLDIFS

or use xargs:

echo dir1 dir2 dir3 | xargs -n 1 cp file1

Both of these will allow you to copy entire directories/multiple files. This is also discussed in this StackOverflow article.

share|improve this answer
    
N2NCopy link appears to be broken. –  Wesley Dec 28 '09 at 19:38
1  
Google Fu - sourceforge.net/projects/n2ncopy –  Fake Name Jul 27 '10 at 11:39

In bash (Linux, Mac or Cygwin):

cat source | tee target1 target2 >targetN

(tee copies it's input to STDOUT, so use redirection on the last target).

In Windows, Cygwin is often overkill. Instead, you can just add the exes from the UnxUtils project, which include cat, tee, and many others.

share|improve this answer

Ryan Thompson's solution:

for x in dest1 dest2 dest3; do cp srcfile $x &>/dev/null &; done; wait;

makes a lot of sense: If write speed of the destination dirs is approximately the same then srcfile will only be read once from disk. The rest of the time it will be read from cache.

I would make it a bit more general, so you also get subdirs:

for x in dest1 dest2 dest3; do cp -a srcdir $x &; done; wait;

If the write speed of the dest dirs are very different (e.g. one is on a ram disk and the other on NFS), then you may see that the parts of srcdir read while copying srcdir to dest1 is no longer in the disk cache when writing dest2.

share|improve this answer

In bash:

for x in dest1 dest2 dest3; do cp srcfile $x &>/dev/null &; done; wait;
share|improve this answer
1  
i don't think this will perform well. in an ideally parallel copy you'd be reading once, writing many times. i think this will do 1:1 reads:writes. maybe if the copies start fast enough and drive cache is big enough you won't actually need to seek the read heads. –  quack quixote Oct 4 '09 at 23:23

Copy the following code into a new text file and save it as "mycopy.bat"

@ECHO OFF
set file= %1
:Loop
shift /1
IF "%1"=="" GOTO Continue
copy %file% %1
GOTO Loop
:Continue

Copy this file to your \windows directory,

Now, bring the command prompt the type : mycopy < source > < target 1 > < target 2 > < target 3 > .. < target 9 >

PS: limitation for only 9 arguments.

share|improve this answer
    
Very cool. I didn't know about the shift command. However, this doesn't copy in parallel. Though it could probably be combined with START to spawn a new shell... –  Goyuix Aug 31 '09 at 14:39

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.