Take the 2-minute tour ×
Super User is a question and answer site for computer enthusiasts and power users. It's 100% free, no registration required.

I am trying to figure out how the Watts is calculated based on the Volts and Amps on power supply stickers.

Higher 12V rail

I am told that the 12V rail is the most important, but I don't know how they calculated the 41A? I understand 41 * 12 = 492 for the Watts, but how do they get 41A from the four 18A?

Update - Sometimes they don't specify the combine Amps number like in this power supply. I guess if the manufacturer doesn't provide the numbers there would be no way to tell the amount of watts the 12V rail provides?

enter image description here

share|improve this question
3  
Each 12V rail is probably rated at 18A max but, in total, the PSU is only rated to supply 41A from all 12V rails. –  sblair Sep 7 '11 at 14:50
3  
The +12V combined current rating for the second PSU would simply be: 380W / 12V = 31.67A (less than 16A + 18A). –  sblair Sep 7 '11 at 15:11
    
Remember that watt = voltamp. manufacturers don't always list both watts and amps, because given the voltage you can trivially calculate one from the other. you might need to do this to get some information. –  jcrawfordor Sep 7 '11 at 16:09
    
@jcrawfordor For DC, yes. But just to be pedantic, the volt-ampere is a different unit from the watt. –  sblair Sep 7 '11 at 16:38
    
I should clarify that difference, because it's relevant when discussing power supplies. Formally, the Watt is a derived unit whose derivation can be simplified to W=v*A - in theory, the units do perfectly correspond. In DC power, this holds true in real usage. For AC power, though, VA is used to refer to the apparent power in a circuit. Because of various factors real power (expressed in W), or the power actually in use, is lower by a a ratio called the power factor. AC equipment will often be labeled with both a VA rating and a W rating, both should be minded. –  jcrawfordor Sep 7 '11 at 19:15

4 Answers 4

up vote 2 down vote accepted

Designing a good PSU is quite an art, especially when balancing power output, stability, efficiency, cost and durability.

Often cheap power supplies will use two or more cheap 12V circuits, which are rated for a relatively low power draw. Better quality PSU's might use multiple higher quality 12V circuits, but others might have a single high quality/power/efficiency 12V power circuit.

Even high quality single rail PSU's may break out that one rail into multiple rails with individual overload protection on each supplied rail.

So, the be quiet! PSU is probably of the last type, it has a single 41A circuit, providing power to 4 rails, where either a total draw of more than 41A or a draw of more than 18A on any one rail will trip the over-current protection.

The Power LC is either an old or cheap PSU which probably has two different cheaper 12V circuits. Don't expect either rail to perform anywhere near the limits suggested.

Personally, I prefer pure single rail PSU's (where you might see 12V 41A as the only spec). You don't need to worry about balancing power over each rail and you don't risk overloading one rail when you add a new device because you've plugged it into a power connector that uses the same 12v rail as your graphics card.

The only problem with a single rail PSU is that since they can potentially supply more current than the cables are rated for, if you have a short circuit you could end up burning out the cables before the overload protection kicks in. This is still very unlikely though, so much so that respected PSU makes are happy to sell single-rail PSU in the consumer market.

If you are unsure about whether your PSU is suitable for your system or not, I've found the eXtreme Power Supply Calculator Lite v2.5 to be an interesting first port of call. Just don't forget to add in capacitor aging factor (see note 4) if you intend to run your computer 24/7 or want it to remail reliable for more than a year.

share|improve this answer

Watch this video tutorial. The tutorial text can be found here.

share|improve this answer
1  
The point of this site is to offer expert advice; referring us to other links to get information is not recommended. Try summarizing the links, and including the links just as a reference –  Canadian Luke Jun 3 '13 at 16:34

If the combined amps is not reported, it's the sum of all the lines together. However, I would double-check that, at least so that you don't go above the rated maximum wattage..

share|improve this answer

41A is probably the total possible amps available to the 12V rails. Each rail can go up to 18A, but not all at once.

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.