Take the 2-minute tour ×
Super User is a question and answer site for computer enthusiasts and power users. It's 100% free, no registration required.

I have a Drobo-FS with DropBear installed via DroboApps which allows me SSH access into the linux operating system which powers the Drobo-FS.

The Drobo-FS file system has a directory which looks like this

# ls /mnt/DroboFS/System
DNAS    avahi    netatalk    samba

Each of the directories listed has a conf or similar directory within it and for me the samba, netatalk and avahi conf files all exhibit an Input/ouput error

# ls /mnt/DroboFS/System/samba/conf
ls: /mnt/DroboFS/System/samba/conf/scratch.smb.conf: Input/output error
ls: /mnt/DroboFS/System/samba/conf/smb.conf: Input/output error

# ls /mnt/DroboFS/System/netatalk/conf
ls: /mnt/DroboFS/System/netatalk/conf/afpd.conf: Input/output error
ls: /mnt/DroboFS/System/netatalk/conf/AppleVolumes.default: Input/output error

# ls /mnt/DroboFS/System/avahi/conf
ls: /mnt/DroboFS/System/avahi/conf/scratch.avahi-daemon.conf: Input/output error
avahi-daemon.conf

I have read that this behaviour is indicitive of a hard-drive failure or a loose cable (I assume connecting the drive to the controller.) However this is not an ordinary Linux box, so my first question is

What device is /mnt/DroboFS/System stored on. I assume it cannot be on a hard-drive in any bay, and must therefore be on some other internal drive or flash memory. If so does this mean my Drobo-FS is faulty?

Also the question has to be asked: why have only the configuration files been affected?

Or could this problem run deeper?


Additionally could anyone with specifically a Drobo-FS and frimware version 1.2.0 provide their versions of the following files?

/mnt/DroboFS/System/samba/conf/smb.conf
/mnt/DroboFS/System/netatalk/conf/afpd.conf
/mnt/DroboFS/System/netatalk/conf/AppleVolumes.default

With that I could replace the seemingly corrupt files with the correct versions.


And finally, if the Drobo itself is faulty, is the RAID (or BeyondRAID) configuration data stored within the hard drives themselves or the drobo. In other words can I move the existing drives to a new drobo without data loss?

Edit: I can answer my own question here. I discovered this is possible if you move all Drobo disks as a "disk pack" to a new Drobo. The order/position of each drive must to be maintained for this to work.


Edit: Result of cat /proc/mounts

# cat /proc/mounts
rootfs / rootfs rw 0 0
/dev/root / jffs2 rw 0 0
proc /proc proc rw 0 0
devpts /dev/pts devpts rw 0 0
none /sys sysfs rw 0 0
/dev/shm /dev/shm tmpfs rw 0 0
/dev/mtdblock/2 /var jffs2 rw 0 0
/dev/sda1 /mnt/DroboFS ext3 rw,noatime,nodiratime,data=ordered 0 0
share|improve this question
    
what does cat /proc/mounts say? –  technosaurus May 31 '12 at 0:50
    
I have edited my answer to include the result. –  Marcus Whybrow May 31 '12 at 1:49
    
Sorry no one's gotten the answer to your question yet. I've got a DroboFS, let me know if you're still having issues. –  bobmagoo Aug 25 '12 at 22:19
    
@bobmagoo I am still having the same issues, although I can now coexist with them. I have since had my entire DroboFS replaced, and the problem still persists. –  Marcus Whybrow Aug 27 '12 at 19:05
    
@MarcusWhybrow Sounds good. Sorry to hear you're still having issues, hopefully it isn't causing any issues using the thing. –  bobmagoo Aug 27 '12 at 19:10
show 3 more comments

1 Answer

ls -ld /mnt/DroboFS/System should tell you and allow you to identify which device it is; if it ain't a symlink to something else it is more likely be the case that your hard drive is faulty so you might need to replace it, assuming the cable is properly connected and intact.

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.