Super User is a question and answer site for computer enthusiasts and power users. Join them; it only takes a minute:

Sign up
Here's how it works:
  1. Anybody can ask a question
  2. Anybody can answer
  3. The best answers are voted up and rise to the top

I replaced my G wifi card for an N card and now I have static through my Creative 4400 speakers.

Any idea how I can solve this without changing the speakers? Strange that the shielding works with G and not N?

share|improve this question
Passing into the "amp" section of the speakers, or via the wiring? You could check that if you could move it closer to those areas, or by using a cell phone :-) When transmitting to tower. Cells are usually is strong enough to cause interferance, and find susceptable entry points. This is assuming it is not passing somewhere more internally in the computer. What is the method for the connection from computer to speaker? – Psycogeek Dec 31 '11 at 14:50
@Psycogeek into the amp which is contained in the subwoofer. I have a splitter on the output from the sound card (X-Fi Music) which goes to headphones which are fine. – Marcus Dec 31 '11 at 16:26

Sounds like you need a low pass filter at the input to your amp. As I mentioned in another answer to a similar question, the filter should have a corner frequency of 1 MHz or so. These are sold as noise suppressors, or if you have a soldering iron, this would be a very simple, cheap project / kit (google RC low-pass filter, use a filter calculator). The audio frequencies that you want (10 Hz to 20 KHz) are so far away from the Wifi spectrums (2.4 GHz to 5.8 GHz, iirc), that the filter's job will be very easy; no need for complicated designs or expensive parts.

I know this is an old question, but it gets a lot of views. This must be a common problem.

share|improve this answer
Do you know if these can be bought with a male female 3.5mm plug ? – GinKin Mar 3 '14 at 12:21

I have a similar creative unit. Pressboard box with subwoofer, and amp. It hears the cell phone tower connection easily. It doesnt have a lot of ventilation slots on the cabinet. Because of that it is possible to shield it with a ferrous mesh or thin sheet of rolled steel (idea) without blocking vents.

With digital, it still can get interferance, but they have optical connection, balanced connection, and sharp on/off signals that either work or dont. The problem here though, is probably the signals going right to the amp and its (antenna like) curcuitry , and the lack of sheilding.

To reduce the effect of the interferance , often you can increase the signal (turn up the volume on the computer to max) And decrease the ammount of amplyfying (turning down the speakers) That would increase the "signal to noise ratio".

Old school amps and tuners, would have been in vented steel enclosures, been grounded, or provided for grounding. High end electronics can have PCBs with layers that provide sheild. You might get away with very simple single metal sheild just leaning there.

I have a simple sheet of thin rolled steel from the hardware store, that I have used before. If something was a problem of interferance, I could just place it under, or over, or on the side of. I could tack it to places on the wood desk. I could just use it to Test quick what the problems are , to move things around.

You could crack open the box, and redesign it a bit, by putting sheilding on the inside. You can "craft" a thin sheet of steel or iron, by gluing black vinyl to it, or painting it black, use it on the outside to block signals. You could just move the speakers and the wi-fi further away from each other.

If that problem becomes solved, this interferance blocker sheet, could be used to test or temporarily fix other interferance issue later. It could be used to redirect (parabola) or block signals also. The sheet can be connected to a devices ground or earth ground, but it is not usually much better that way.

A positive outlook of the problem , you have a pretty strong wi-fi going :-) so that's good.

share|improve this answer

I am having a similar problem but the cause is the wireless network adapter I installed recently (D-Link AC1200 Dual Band). It runs on the new AC standard but is backwards compatible with all other versions. My computer is out of range of the 5Ghz signal but the 2.4Ghz router is within range. I was able to pin-point the problem by running As the website needed access to my wireless card to send and receive data packets, the amount of static coming from my speakers became constant.

Like others have posted, check to see what frequency your wireless network card is running. If it is only using the 2.4Ghz band then that is where your interference (speaker noise) is coming from.

If your wireless network card is a dual band model (has both 2.4Ghz and 5Ghz bands) try to connect to a 5Ghz band router via wifi and see if that helps.

Unfortunately, since my desktop PC is too far away to "see" the 5Ghz wireless router near me I cannot test if the change in wireless frequencies will make a difference.

share|improve this answer

You must log in to answer this question.

protected by JakeGould Nov 2 '15 at 18:15

Thank you for your interest in this question. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site (the association bonus does not count).

Would you like to answer one of these unanswered questions instead?

Not the answer you're looking for? Browse other questions tagged .