Take the 2-minute tour ×
Super User is a question and answer site for computer enthusiasts and power users. It's 100% free, no registration required.

I understand the reason public IP addresses are necessary to be that if we only had MAC to move data between one host and another, the entire Internet would be one massive, flat network. But what is the need for private IP addresses? Why can't routers just connect to local hosts using their MAC address?

share|improve this question
    
This question may spawn more opinions than answers, so I don't know if it's appropriate. But probably the best reason is because you can't really communicate with a MAC address, because communications on a network typically take place with the Internet Protocol. You'd need a new protocol, and I don't see why you'd want that (it'd only cause more problems and complications...) There's more, but I guess i'll leave that to the pros. –  John Chadwick Jan 12 '12 at 4:49
    
Heh, MACs are for local ethernet segment communications. Read up on OSI layers to better understand abstraction of communications. –  Fiasco Labs Nov 16 at 4:58

6 Answers 6

up vote 5 down vote accepted

The answer is your software applications and operating system are designed to communicate using TCP/IP, not directly with Ethernet MAC addressing.

So regardless of whether the remote computer/node you wish to communicate with is in your local network or in some other network halfway round the globe, that logical link is established with TCP/IP. That way applications just define the destination IP address in the IP packet, fill it with data (which is actually packed into a TCP/UDP segment), and send it along the way without having to worry how the underlying layers deal with the actual transmission.

It is the operating system's networking stack that determines if the IP address is local or remote:

  1. If local network, look for MAC address corresponding to that IP address and send the IP packet direct, which is in an Ethernet frame.
  2. If remote network, look for MAC address of default gateway router to send the IP packet, also within an Ethernet frame. The router retrieves the IP packet from the frame, looks at the address and determines the next node (and its MAC address) to pass it along, and sends it that direction in another Ethernet frame.

Note: it is totally possible for IP packets to be delivered in another data link protocol other than Ethernet (guess what, your dial-up or DSL modem is not connected to your ISP via an Ethernet cable). And applications should not have to care so as long as the destination IP address is reachable. It is also totally possible to wrap other networking protocol data (that is not an IP packet) in an Ethernet frame for transmission.

share|improve this answer
    
please explain this "it is totally possible for IP packets to be delivered in another data link protocol other than Ethernet" a little more. –  JAVA Nov 14 at 11:01
    
how can ethernet frame can be understood by the other data link protocols? –  JAVA Nov 14 at 11:04
    
Take for example the traditional dial up modem used in the old days to connect to the Internet - do you connect an Ethernet cable to it? Nope. Modems commonly used Point-to-Point Protocol (PPP) as the data link layer, which carries the IP packets to the ISP. It is not the Ethernet frame that Ethernet network adapters and hubs/switches use to carry IP packets. –  icelava Nov 14 at 12:21

One reason is because MAC addresses aren't really "routable". IP is, so it's easier to keep IPs for addresses internally and externally. As well, you don't access other computers based on MAC address alone, you use IP. Te router then decides if it's destined for internal or external

share|improve this answer

Ultimately, all packets are delivered to a MAC address. When an IP packet arrives at your router and the NAT table shows that it is destined for your private address 192.168.1.10, the router will do a look up to see what the MAC address of 192.168.1.10 is, and send the packet to that MAC address.

However, a MAC address is a layer 2 address, and by definition only allows communication between items on the local network. So the question of "why private addresses rather than MAC address" assumes that all non-public networks are simple single flat networks.

There are almost no private corporate networks that consists of a single LAN, and many domestic environments have multiple networks. In order to route between these networks, you need a layer 3 protocol such as IP.

So a different way to phrase your question would be "Why don't router manufacturers and OS developers create a layer-2-only local network in the specific cases where layer 3 is not absolutely necessary?". And the answer to this question is that it would not be worth creating a niche solution to a scenario where the existing general solution already works perfectly. There would be no benefits whatsoever.

share|improve this answer

Network communication is divided into multiple layers. The figure here shows OSI model. Each layer has a purpose of its own. From the bottom of diagram

i. Physical layer: this layer is the actual medium which connects devices, it may be a cat5 cable,optica fibre etc. .

ii) Data Link layer: this layer takes care of physical addressing and packet switching , checksum etc.

iii) Network Layer: This layer takes care of logical addressing and routing packets.

and so on

This helps separate various functions of the network stack . so that layers are not dependent on other layers.

Now coming to your question.

MAC address is at data link layer, whose function is physical addressing . Network layers function is to provide a logical address to a communication node, So when you are communicating between two devices they have to be addressed by their network address. Also they may not even have the same data-link layer i.e therefore one of the nodes may not even have a MAC address.

enter image description here

share|improve this answer

Also note that MAC addresses are not used in all types of network media.

For example, the protocols used on point-to-point connections such as T1's (PPP, HDLC) don't.

share|improve this answer
    
Interesting point of view ! –  Karthik Balaguru Oct 4 at 20:11

If MAC were to be used for routing, your routing table would contain routes to each node on network because MAC addresses are different for every manufacturer.

IP is like a standard platform for network devices from different manufacturers to communicate. And with use of IP, you can summaries a route to many devices on a network saving bandwidth and resources. The OSI model provides more insight to how networks work.

Without this standard, I believe networking itself wouldn't be developed as it is today.

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.