55

Many times, I have seen resolution of 1080p and I know that it means 1080 pixels but I also have seen specifications on some HDTVs to be 1080i. So, I want to know the exact difference between them and whether 1080i video quality is available for the laptops too.

I googled and found out that at some sites, they mention 1080P rather than 1080p. Is there any difference between the two or they represent the same thing?

Rev1: Now I know that 1080p means 1080 horizontal lines of vertical resolution in a ___p____rogressive-scan video_

4
  • @BrownE I've mentioned in my question that I Googled already but didn't got satisfied answer and I want to know that this quality is available for PC's or not.
    – avirk
    Apr 7, 2012 at 2:48
  • You know how complicated this can get , when it is rather simple. the transport for the data can still be done interlaced, even if the picture is progressive, and even if the display is progressive. There is a huge difference between them, one is interlaced, now back up again, that doesnt mean it isnt progressive :-) research those 2 terms instead, the whole information on it gets thick because of the many possibilities.
    – Psycogeek
    Apr 7, 2012 at 2:58
  • 1
    very detailded explanation is in wikipedia. why not to use that?
    – Cougar
    Apr 7, 2012 at 5:54
  • 3
    Maybe this would be a good fit for the proposed "Consume Electronics" group? area51.stackexchange.com/proposals/33064/consumer-electronics
    – Pete
    Jun 7, 2012 at 20:25

5 Answers 5

63
+50

I see a range of problems in the answers and comments here (even in some highly-voted answers that provide otherwise very good information) that span from minor deficiencies that need explanation to some serious inaccuracies, so I think that some clarification is needed.

The question is specifically: What is the difference between 1080p and 1080i? so I will start by outlining the main similarities and differences, I'll add some tips on how to choose the best format and then I will proceed to explain the problems that I found here.

Some of the information presented below is adapted from my answer to Interlacing on a computer monitor but is rewritten to strictly stick to the subject of the difference between 1080p and 1080i.

Note

Please note that this answer is specifically about HDTV and talks about signals and resolutions that can be transferred with a standard HDMI cable. Other resolutions and frame/field rates are certainly possible but standard HD TV sets, game consoles, Blu-ray Discs etc. use only certain resolutions and frame/field rates described below (or at least they did at the time of writing this answer). Specifically this answer doesn't talk about: Ultra-high-definition television, Super Hi-Vision, Ultra HD television, UltraHD, UHDTV, UHD, 4K, 8K or anything beyond 1080p and 1080i that this question is about.

Resolution

Both 1080p and 1080i have 1080 horizontal lines of vertical resolution which with a widescreen aspect ratio of 16:9 results in a resolution of 1920 × 1080 pixels (2.1 megapixels). It is not true that 1080i has a lower vertical resolution than 1080p.

Frames vs. fields

1080p is a frame-based or progressive-scan video where you are dealing with frames. You have frame rate and it is expressed in frames per second.

1080i is a field-based or interlaced or interleaved video where you are dealing with fields. You have field rate and it is expressed in fields per second.

A field contains half of the lines of the frame, either even lines or odd lines, and if one field is composed of even lines, then the next one will be composed of odd lines and so on.

Frequencies

1080p has a frame rate of 25 frames per second for TV in PAL countries, 30/1.001 frames per second for TV in NTSC countries and 24 frames per second for cinematography.

1080i has a field rate of 50 fields per second for TV in PAL countries and 60/1.001 fields per second in NTSC countries.

(Note that it is not 30 frames and 60 fields per second for NTSC but actually 30/1.001 and 60/1.001 which is approximately 29.97 and 59.94 but the difference is important. Read about the NTSC color encoding on Wikipedia to see why.)

How to think about it

1080p at 25 frames per second: Imagine that you are shooting 25 pictures per second and storing them as bitmaps. Every frame is a full picture from the given instant. Every pixel in that frame was captured at the same time.

1080i at 50 fields per second: Imagine that you are shooting 50 pictures per second but storing only half of the bitmaps every time - sometimes you store the odd lines and sometimes the even lines. (Note that it is not the same as storing pictures with lower vertical resolution.) Every field is a half of a full picture from the given instant. Every pixel in that field was captured at the same time.

50 halves ≠ 25 full pictures

Contrary to some comments here, interlaced video at 50 Hz does not mean that 25 full pictures per second are shown. It means that 50 halves of pictures are shown but those are halves of 50 different pictures that were shot at 50 distinct moments of time in every second. You not only don't have 25 full pictures per second - you don't have any full pictures at all.

Problems with 1080i

Interlacing causes a lot of problems. For example you can't easily:

  • scale the video
  • rotate the video
  • make video slow motion
  • make video fast motion
  • pause the video
  • grab a still picture frame
  • play video in reverse

without doing some tricks and loosing quality. You don't get any of those problems with progressive video. In addition the video encoding is harder because the codec never has a full frame to work with.

Problems with 1080p

The drawback is that 1080p as currently in use has a frame rate that is only half of the field rate of 1080i so the motion is noticeably less fluid - in fact it's exactly twice less fluid which is a lot. You can see it on large flat TVs that often deinterlace the video to be able to display it on their LCD screens (that, unlike CRT displays, are progressive in nature) which is the cause that they display picture of very high resolution but with jerky motion and some deinterlacing artifacts.

Another problem is that usually 1080i is required for TV broadcasting which means that 1080p is simply out of the question for some applications.

Best of both worlds

Using progressive 1080p with 50 or 60/1.001 full frames per second in the future has a potential to eventually solve the above problems but it will require a whole new range of studio equipment including cameras, storage and editing systems so it probably won't happen anytime soon. The widely used SDI standard for connecting HD video equipment doesn't have enough bandwidth.

Currently the only way to have a fluid motion with progressive scanning is 720p that has a frame rate that is two times faster than 1080p but the resolution of only 1280 × 720 pixels (instead of 1920 × 1080 pixels) which may or may not be a problem for some applications. There is no 720i.

Conclusion

There is no one clear winner here.

Update: Here are some general guidelines to choose the right format:

  1. Is it for high-definition TV? Use 1080i or whatever is required.
  2. Is it for standard-definition TV? Use 720p and then convert to 576i or 480i.*
  3. Is it for Internet and resolution is more important than fluid motion? Use 1080p.
  4. Is it for Internet and fluid motion is more important than resolution? Use 720p.

(It all assumes that 1080p has a frame rate of 25 or 30/1.001 frames/s, 1080i has a field rate of 50 or 60/1.001 fields/s and 720p has a frame rate of 50 or 60/1.001 frames/s as is currently the case. Hopefully a high resolution progressive format like 1080p with a frame rate of 50 or 60/1.001 frames/s or maybe even higher will make this recommendation obsolete in the future.)

*) For number 2 make sure that your 720p has the frame rate of 50 fps if your target format is PAL or SECAM and 60/1.001 if your target format is NTSC (unfortunately it means that there is no format that can be converted to both PAL/SECAM and NTSC). The reason I recommend using 720p for recording is to greatly simplify the edition process when every frame is complete with no interlacing (throwing out every other line at the end is easier than creating the missing lines if you need them) and you have some extra resolution to work with so you can for example zoom the image slightly without making the result look blurry. (If anyone has any bad experience of using 720p to prepare material for SD PAL or NTSC TV broadcasting then please comment so I could update this recommendation.)

Explaining problems

These are the parts that I found in the answers and comments here that I think need some explanation:

Progressive Scanning is more desirable in almost every case.

I think that progressive scanning is indeed better in every respect, but if we are not talking theoretically about the idea of interlacing but specifically about 1080p and 1080i standards as used today, then one has to take into account the fact that 1080i is often required for TV broadcasting and converting 1080p to 1080i would result in jerky motion.

P is better than I in most cases i believe, which is the important bit.

Again, yes, progressive is better than interlaced all other things being equal, but progressive video with frame rate that is two times smaller than the field rate of interlaced video (which is the case with 1080p and 1080i) is something very different, especially if interlaced video with high field rate is required for TV broadcasting and the high field rate cannot be reproduced from progressively recorded material with lower frame rate.

[In 1080i] all the odd lines are displayed, followed by all the even lines. This means that only 1/2 the resolution (540 lines or pixel rows) is displayed on the screen at any give time - in other words, only 540 pixel rows are displayed at any given time.

No. For LCD all 1080 lines are always displayed, for CRT displays usually much less than half of of the lines are displayed at any given time which is equally true for both 1080i and 1080p.

The phrase "only 540 pixel rows are displayed at any given time" is extremely misleading. All 1080 rows-of-pixels usually are displayed at once (and even if they weren't, they'd still appear to be to the human eye), but only half of them will be updated in any given frame. It's effectively the refresh-rate, not the resolution, that's cut in half.

While it is true that the phrase "only 540 pixel rows are displayed at any given time" is extremely misleading, it is not true that the refresh-rate is cut in half, because in 1080i the refresh rate is two times faster than with 1080p so it is actually the other way around.

1080i60 means that you're getting 60 half frames (alternating lines) per second, so only 30 complete frames per second.

With 1080i60 you actually get less than 60 fields (or "half frames") per second, but it doesn't mean that you get 30 (or almost 30) complete frames per second. In fact you don't get even a single complete frame per second.

More resources

This is what I consider the best resource on the subject of field-based (aka interlaced or interleaved) and frame-based (aka progressive-scan) video:

See also the following articles on Wikipedia:

I hope it somewhat clarifies the subject.

10
  • I like this answer, but it is still unclear to me whether a progressive frame is "scanned" or "captured". That is, do all of the pixels of a frame have the exact same timestamp, or is the timestamp of the first pixel about 1/60th of a second older than the last pixel of a given frame?
    – Les
    Oct 26, 2012 at 13:07
  • 4
    Now this is an answer. You interested in blogging about this for the SU blog? Oct 26, 2012 at 14:31
  • Excellent answer! Although I'll stand behind my "serious inaccuracy" of "Progressive scanning more desirable in almost every case". ;) Oct 26, 2012 at 23:12
  • @Les Every pixel of a frame in progressive video is captured at the same time (all have the same timestamp). That is why you can take a pause and you don't have skewed objects that are in fast motion. (Also, every pixel of a field in interlaced video is captured at the same time.) The term "progressive scanning" is a little bit misleading, it used to be called "sequential scanning" which is maybe better, but all it means that it is just noninterlaced with no reference to the actual time of capturing every pixel. Maybe I'll update my answer to make it more clear.
    – rsp
    Oct 27, 2012 at 12:06
  • 1
    @techie007 I actually agree that progressive scanning is more desirable in almost every case, and in fact I hate the fact that interlaced video is still being used today for HDTV just because some 90 years ago people couldn't build a mirror drum-based television fast enough for progressive scanning of 64 lines of resolution. Though I'm not sure if specifically 1080p is more desirable in almost every case than 1080i. In any case, the "serious inaccuracies" was not really meant to describe your comment in particular and I think I really have to change my answer to make it more clear. Thanks. :)
    – rsp
    Oct 27, 2012 at 12:28
41

These are how the image is 'painted' onto the screen.

The "i" in resolutions represents 'Interlaced'. Basically meaning every other (horizontal) line is drawn in one frame, and then the opposite lines are drawn in the next frame, leaving it up to your eyes/brain to put the two frames into one complete one.

The "p" means 'Progressive', which means all the lines are drawn one at a time, in sequence, for each frame.

If the video equipment and signal involved can handle it, Progressive Scanning is more desirable in almost every case.

There is no difference between "1080P" and "1080p", both are acceptable ways to write it.

7
  • 7
    Also, in P is better than I in most cases i believe, which is the important bit.
    – Journeyman Geek
    Apr 7, 2012 at 3:05
  • @JourneymanGeek True enough, probably worth mentioning. ;) Apr 7, 2012 at 3:06
  • 9
    Actually, interlaced presentation allows the refresh rate to be cut about in half without generating perceptible flicker. In both cases it's up to a combination of your eyes/brain and the phosphor/LCD/LED/whatever persistence to make the image appear to be continuously visible with no flicker. Interlaced was most useful with phosphors on CRTs since they have a limited persistence, whereas LCD, et al, can be made to persist until the next refresh. Apr 7, 2012 at 3:06
  • 1
    @techie007 would you like to read last two lines of my question and then edit your answer if you can. I don't know why suddenly this question got good intention.
    – avirk
    Jun 10, 2012 at 10:12
  • 2
    @avirk No worries man, that's how it works. ;) Oct 26, 2012 at 15:38
17

1080p represents 1920 pixels displayed across a screen horizontally and 1080 pixels down a screen vertically. However, unlike 1080i all pixel rows or lines are displayed progressively, providing the most detailed high definition video image that is currently available to consumers.

1080i represents 1920 pixels displayed across a screen horizontally and 1080 pixels down a screen vertically. This arrangement yields 1,080 horizontal lines (pixel rows), which are, in turn, displayed alternately. In other words, all the odd lines are displayed, followed by all the even lines. This means that only 1/2 the resolution (540 lines or pixel rows) is displayed on the screen at any give time - in other words, only 540 pixel rows are displayed at any given time.

Difference between 1080p and 1080i may be good link for you and also see the yahoo answer for the clarification.

4
  • 2
    This sort of information is just fine as an answer if you flesh it out a bit. Go ahead and edit your answer to include a little more details from the links - maybe a brief summary of the information from those pages - and you'll be good to go.
    – nhinkle
    Apr 7, 2012 at 3:28
  • @nhinkle I added some definition as you told. Is it ok?
    – ItsBegin
    Apr 7, 2012 at 3:40
  • 2
    That looks much better @ItsBegin, thanks for the edits! I made a couple more little changes for you to touch up the formatting.
    – nhinkle
    Apr 7, 2012 at 3:42
  • 8
    The phrase "only 540 pixel rows are displayed at any given time" is extremely misleading. All 1080 rows-of-pixels usually are displayed at once (and even if they weren't, they'd still appear to be to the human eye), but only half of them will be updated in any given frame. It's effectively the refresh-rate, not the resolution, that's cut in half. Apr 7, 2012 at 9:25
8

The i is for interlaced (each frame only updates half the lines each frame, as is the case with pure-HD television. The p is for progressive, which updates the whole screen.

1080i60 means that you're getting 60 half frames (alternating lines) per second, so only 30 complete frames per second.

Sometimes an interlaced signal will be a progressive signal split into half frames ( e.g. Some Panasonic cameras have 1080p30 sensor output but (for some reason) write it out to a 1080i60 file. A more common case is of actual half frames, and if you freeze frame you'll see discrepancies between alternate lines in the still image.

1080p60 means 60 full frames per second.

Why have interlaced frames at all? Good question. Back in the days of analog video, interlacing was used to allow faster refresh for a given bandwidth and it made some sense. Supporting interlaced frames for digital video seems to be something of a blind alley.

0

One point I don't see mentioned here that I personally find significant... Many 4k TV's have built-in software to up convert a full HD picture to "NEAR 4K". However they must originate from a 1080p source. Many cable boxes are only capable of producing a 1080i picture. Just another consideration I felt compelled to add. CDEricson

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .