So, i have old HDD and i need to get information from it but small problem that HDD is dead, can anybody explain proccess how peoples get information from it. Is this depends from model of HDD?
Thnx for any information about this question.
This answer focuses on exchanging HDD platters,
you really should try all other methods before this, some listed here:
Now, if you have another disk that is working and decided to remove protective covers from broken HDD then remember to:
You will need two hard disks, one broken and one working. Both disks will be wasted and rendered useless during recovery process. Other tools that you need is torx driver (T8 is common one), few small and sharp flat-blade screwdrivers, and some imagination.
Start with working HDD by removing top cover:
If there is more than one platter inside you should immediately put cover back and get some special tools for holding platters and lifting them out. Platters must be aligned properly so you need to make sure that they don not move in relation to each other.
For broken disk inspect all components inside, try to rotate platter from top of bearings (do not touch platter surface), check platter surface for any visible scratches. Try to keep platters covered while you are not working on it. Best if you can take some sharp hi-res pictures, put covers back and take your time inspecting pictures, usually you could see many things that is not visible for naked eye.
Remove actuator arm if needed:
If actuator arm has special separate parking zone then you want to check if platters can be removed/inserted without removing/rotating actuator arm. If needed you can try to loosen head parking zone bearing screw.
If there is no parking zone outside platter then you probably need to take actuator arm with heads out. In this case use your imagination, how to keep heads in good condition and how to get heads back to platter surface. I have used small plastic square (5x5mm) or taped hard foam (in pictures, easily cutted to right size and thickness), thickness should be same as platter thickness or 5-10% more to avoid collisions with platter edge. Use material that does not damage heads.
Note: My old Maxtor in images does not have special parking zone which means that heads will always "touch" platter.
Remove locking ring that holds platter in place:
While loosening screws that hold ring in place you also need to hold platter in position. Do not allow any uncontrolled platter rotation. Use holes or screws in ring to hold it, loosen and tighten lightly all screws before removing them (if you remove screws right away then at least last screw will take all pressure and you need more torque for opening it, try to keep pressure for screws equal).
Now you can use your imagination again if you don't happen to have hard disk platter removal tool in your arsenal. Any rubber edged tool that fits comfortably between platter edge and case will do. Make sure that platter is held and balanced well, do not force platters out.
Repeat above steps for broken HDD
Be extra careful while removing heads or while moving actuator arm. Again, it could help if you can get drive spinning before trying to move heads. Here it can be better to remove all parts that might be too close to platters as you are not going to put platter back to broken drive. Avoid scratching platter at all costs.
Insert platter from broken HDD to working one:
Finally try to put it back together. If actuator arm removed or there was no parking zone for heads you can use foam between heads to move them back on track (platter surface), again carefully, be steady.
Do not turn actuator arm back in original position by hand, instead try to rotate platter and see if it magically goes to right position (again: don't touch surface, this is not CD/DVD). If you need to force heads to some parking position then use some small soft spring for pushing actuator arm to right direction, again: rotate platters.
If you aren't ready to pay large amounts of cash for data recovery and want to attempt to do it yourself, you can TRY it, but keep in mind that these companies get paid the big bucks because it's hard to do.
My Hard Drive Died, one of the various commercial data recovery companies, actually has videos and presentations showing exactly how they recover data from hard drives, depending on exactly how the drive failed.
It's interesting stuff to read and watch, but if the data is worth more than the cost of recovery, then you're best off to send it to the professionals.
If all else fails, you can send your drive off to a professional recovery service.
Typically, at minimum it costs $500 and can go upwards of $2,000.
Here is one of the reputable ones (this used to be the company named "Ontrack"): http://www.krollontrack.com/data-recovery/data-recovery-services/hard-drive-recovery/
The bottom line is that for professional recovery services it all depends on how much that data is worth to you.