Super User is a question and answer site for computer enthusiasts and power users. Join them; it only takes a minute:

Sign up
Here's how it works:
  1. Anybody can ask a question
  2. Anybody can answer
  3. The best answers are voted up and rise to the top

My computer has a USB port that appears to be too loose, with attached devices exhibiting too much play where the USB plug is inserted into the port. The port still works, as devices continue to communicate correctly when attached to this port. The port itself is tightly attached to the computer chassis. Should I attempt to tighten the port? Is it at risk of eventually failing?

share|improve this question
I have a USB port where the plastic lip in the centre broke out, it still works, although connectors are a bit loose now of course. – Baarn Sep 8 '12 at 21:50
up vote 4 down vote accepted

I would say most likely no. If the physical housing is still soundly attached to the case as your description sounds like. Then the only thing I think of is that the center plastic tab that holds the metal connectors is missing/broken. If it is missing that ports effectively dead you will need to either replace the part that the usb is attached to [daughter card or system board depending on model].

If you happen to still have the plastic tab or it hasn't fallen out yet it MIGHT be possible to glue it in place again but the chances of getting a perfect fit like is needed are low.

If you continue to use it with no plastic tab to keep the pins straight they will short out at some time which can cause any thing from the pc not booting to loss of just that port. If it starts causing reboots due to shorting even bumping the table could cause you to loose important data.

A picture of the broken port would help explain the situation better.

Here is the best image I could find for the purpose.

Usb port Behind the white rim is a metal housing which is where the port actually begins. If that housing is attached to the pc and not bent out of shape it should hold the usb devices well. The white tab shown with the 5 pins is what actually makes contact electrically. Which you said was intact. Since you say that is in place the only thing left would be the springs at the bottom of the image. They could have been bent out of shape or flattened. it might be possible to use a paper clip or a dental pick to slide under them and bring them back to tension. If they were flattened though it is likely they wont stay springy for long since they are so tiny you will be hard pressed to find a spongy/springy material to slide under them to keep the tension.

share|improve this answer
The plastic tab is still intact and is not loose. – bwDraco Sep 10 '12 at 14:37
Any other possible reasons? I tried to tighten the outside housing of the port, and while devices now snap and hold tighter in the port, the connector still wobbles excessively. – bwDraco Sep 10 '12 at 17:41
I just checked the affected port against known good ports, and the metal springs both at the inside top and bottom of the port are indeed responsible. – bwDraco Sep 11 '12 at 3:39
Just adjusted the springs, and it is no longer loose. – bwDraco Sep 11 '12 at 4:04
I had a laptop where a specific port broke, needed a motherboard replacement... which broke again. Supergluing it back on has worked for some reason. You will notice if its broken tho – Journeyman Geek Jan 22 at 11:39

Clean these ports with petrol. Sometimes edges gets covered by some black colored thing. Locally we call it that carbon has covered the contact points due to which ports are not working.

share|improve this answer
Welcome muddsar, can you provide some more knowledge behind this? It would maybe helpful for others. – nixda Dec 30 '12 at 18:20
A dirty contact does not make a loose port ... – DavidPostill Jan 22 at 10:10

You must log in to answer this question.

protected by bwDraco Jan 22 at 9:28

Thank you for your interest in this question. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site (the association bonus does not count).

Would you like to answer one of these unanswered questions instead?

Not the answer you're looking for? Browse other questions tagged .