Super User is a question and answer site for computer enthusiasts and power users. Join them; it only takes a minute:

Sign up
Here's how it works:
  1. Anybody can ask a question
  2. Anybody can answer
  3. The best answers are voted up and rise to the top

Is there something wrong with my SSD drive ? It's still under warranty so I can replace it ;)

SMART Error Log Version: 1
ATA Error Count: 1
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 1537 hours (64 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle

  After command completion occurred, registers were:
  -- -- -- -- -- -- --
  84 51 00 00 00 00 00

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec 00 00 00 00 00 00 00      00:19:35.000  IDENTIFY DEVICE
  e5 00 00 00 00 00 00 ff      00:19:34.500  CHECK POWER MODE
  b0 da 00 00 4f c2 00 00      00:17:57.100  SMART RETURN STATUS
  ef 02 00 00 00 00 a0 00      00:17:57.100  SET FEATURES [Enable write cache]
  ef aa 00 00 00 00 a0 00      00:17:57.100  SET FEATURES [Enable read look-ahea

More generally: Are there specific techniques for SMART on SSD drives?

share|improve this question

migrated from Apr 1 '13 at 0:44

This question came from our site for system and network administrators.

"Here's a wall of text, do I have a problem?" isn't one of the best presentation methods. In future questions, try to identify what it is you saw within the output that caused you to be concerned. – Andrew B Mar 31 '13 at 17:50
Look at the error message at the end. – Spacedust Mar 31 '13 at 17:55
I can find the error. My point was more that if your presentation requires people to search the entire output to find the message that may be concerning you, many people aren't going to take the time to look for it. – Andrew B Mar 31 '13 at 17:56
Edited my message. Please check again. – Spacedust Mar 31 '13 at 17:59
That's a little bit better. Note that the detailed output wasn't necessarily a bad thing, it's just a good idea to identify outside of it what message was concerning you so that people have a point of reference. – Andrew B Mar 31 '13 at 18:01
up vote 2 down vote accepted

I don't know, if ssds support this, but for a normal hdd, if you suspect a problem, you let it do a short or long selftest:

smartctl -t short /dev/sdX
# or
smartctl -t long /dev/sdX

It will normally tell you how long this takes. Leave you computer on for that time. Then check the result with smartctl -a /dev/sdX. I recommend keeping a trail of smartctl -a outputs somewhere to compare what changed.

All that said, I really don't know, what SSDs these days support when it comes to smart. The last time I had an SSD connected to my main box, its smart was… well, it could use some improvement.

share|improve this answer
# 1 Short offline Completed without error 00% 1707 - – Spacedust Apr 7 '13 at 22:15
Did any other attributes change? That might help identify possible issues. – Elrond Apr 8 '13 at 21:51
No, only that one ;) – Spacedust Apr 8 '13 at 22:14
# 1 Extended offline Completed without error 00% 1711 - – Spacedust Apr 8 '13 at 22:15
You've got my vote – Spacedust Apr 9 '13 at 11:25

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .