Take the 2-minute tour ×
Super User is a question and answer site for computer enthusiasts and power users. It's 100% free, no registration required.

I'm the proud new owner of a Raspberry Pi and have it up and running now with VPN/SSH/X11VNC.

This morning I had it booted up on a TV on my table where I was working on it. Went to work and have been working on it remotely via VNC over my VPN just fine. I came to a point where I had to reboot which all went fine, I've logged back in and reconnected to the VNC session – however the resolution is stuck in 656×416, so not really usable.

Now I'm guessing that this is because the Pi booted up without the TV/HDMI monitor being on.

Is there a way by terminal or otherwise I can force it bigger?

I read about HDMI groups and modes you can put in a config file then reboot, but wasn't sure if this would then affect my monitor when I get home and try to log on locally.

Or is the key here to establish what HDMI group/mode it is using when using locally and then adding to the config file used on bootup?

share|improve this question
    
Just answered my own question, there is an option to force it to use hdmi. - In /boot/config.txt uncomment the line hdmi_force_hotplug=1 - doesnt change resolution but fixes me not being about to vnc properly after a reboot with screen off –  Ben Gillam Aug 22 '13 at 12:06

1 Answer 1

xrandr can do what you need. If your terminal is running under X (eg via VNC) you should be able to see all available modes using:

xrandr

If you're not under X connect just set your display:

DISPLAY=:0 xrandr

This will display available modes and available output devices. My pis are all headless so I don't have appropriate output but here's one a snippet from another device:

Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 1920 x 1920
DFP1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 160mm x 90mm
   1920x1080      60.0*+   50.0     30.0     25.0     24.0  
   1776x1000      60.0 +   50.0     25.0  
   1600x1200      60.0  
   1680x1050      60.0     50.0  
   1400x1050      60.0     50.0  
   1280x1024      75.0     60.0     50.0  
   1440x900       59.9     50.0  
   1280x960       75.0     60.0     50.0  
   1366x768       59.9     49.9  
   1360x768       60.0     50.0  
   1280x800       75.0     60.0     50.0  
   1152x864       75.0     60.0     50.0  
   1280x768       74.9     59.9     50.0  
   1280x720       60.0     50.0  
   1024x768       75.0     70.1     60.0     50.0  
   1152x648       60.0     50.0  
   800x600        72.2     75.0     70.0     60.3     50.0  
   720x576        50.0  
   720x480        60.0     50.0     30.0  
   640x480        75.0     72.8     60.0     50.0  
CRT1 disconnected (normal left inverted right x axis y axis)

To change a display mode specify the name (DFP1 in the example above):

xrandr --output DFP1 --mode 1024x768
share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.