Super User is a question and answer site for computer enthusiasts and power users. Join them; it only takes a minute:

Sign up
Here's how it works:
  1. Anybody can ask a question
  2. Anybody can answer
  3. The best answers are voted up and rise to the top

I have been using a Corsair Force 3 (120GB) SSD since last 1.5 years. Yesterday, the laptop freezed suddenly and I had to hard reset it. Then it refused to boot as if no HDD was installed. This has happened earlier a couple of times. Usually, after a restart it used to work like normal but yesterday even after a few restarts the BIOS won't detect the HDD. I connected it to a different computer using USB to SATA converter and it still won't get detected.

From what it seems, the controller has gone kaput but there are chances that the data is still intact. I just need to confirm if what I am thinking is right. Also, is there any way I can purchase an exactly similar SSD and swap the controller / memory chips ? I know this would require some BGA level soldering but I can give that a try.

share|improve this question
    
You are correct in your assumption, the controller (or just the physical SATA interface) is failing. Or maybe it got a power surge and fried itself silly. But I do wish you luck in this endeavor – Deryck Feb 2 '14 at 16:09
    
Have you been keeping the firmware up-to-date? Many data-recovery firms exists, but they are costly. If you have not updated the firmware there is a slight chance it might work. If you can get a computer to recognize it enough to preform the update do that first. Otherwise a data recovery company, or you can solder it at your own risk. – cybernard Feb 2 '14 at 18:34
    
I haven't performed a firmware update. I tried updating the firmware but for the tool to make an update, the SSD should be detected and shown up in the list. – Madhur Feb 2 '14 at 20:15
up vote 1 down vote accepted

With SSDs its highly unlikely that you'd be able to get and data back unless it decides to be recognised again. I would try hot plugging it to a Linux computer watching the output of syslog (or wherever kernel measages go to on your machine)

Replacing the controller will not work, as it contains memory of how the data is mapped onto the NAND flash.

As a last resort I'd recommend putting the drive in cold and dry environment for a little bit. As weird as it sounds electronics work better at lower temperatures. take care to minimise condensation however.

When you do connect it back up, start copying data as fast as possible, with dd preferably.

If the data is truely important, you should consider data recovery company

share|improve this answer
    
Thanks for your answer Yarek T. I'd try hot plugging it to a Linux machine and watch for dmesg maybe. How do I put the drive in cold and dry environment ? How much cold should it be ? Should I put it inside a bag in a refrigerator ? Will that help ? – Madhur Feb 3 '14 at 17:51
    
Sealed bag, wrapped in a paper tissue should do it. After maybe an hour take it out, Leave it for about 2 minutes, and plug it in. Be ready to initiate dd copy if it gets recognised. You'd need as much space as the disk is in size. Make sure everything is dry before you plug anything in. Water can damage your working computer =/. Good luck – Yarek T Feb 4 '14 at 17:41
    
Will try that and let you know ! Thanks a ton!! – Madhur Feb 4 '14 at 17:44

OK good answers here: The controller has failed or the firmware corrupted. CHECK

You are right about your data still being in tact. There is a 99.9% chance of this and a full recovery. That is unless you make the situation worse with a bunch of frivolous suggestions of how to recover it yourself. (that is unless of course you have a NAND reader and utility to put it all back together.)

Horrible answers: Suggesting to put the drive in a cold and dry environment. This is a solid state drive right? Ok just checking.

SSD drives are great until they stop working. Same as a USB Flash Drive.

When a SSD drive is no longer recognized by any computer you will need to have a company that is experienced with NAND recovery and has the proper tools to do it.

The chips need to come off in this case, and be read by a NAND reader. Yes it can be expensive however there are companies out there that will work a good deal out with you. SERT Data Recovery has been known to be very reasonably priced and has all the latest technology to recover all sorts of data loss, including SSD.

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.