0
votes
1answer
49 views

Drive still usable if Seatools reports errors?

I have a Seagate 3TB Expansion Desktop drive that was part of a Linux RAID 6 array that failed. I eventually did a zero fill both through Seagate DiscWizard and via Linux dd, neither reported errors. ...
0
votes
2answers
302 views

Mark bad blocks as unusable on NTFS using linux

one of my laptops are using windows and after a certain impact it doesn't boots up anymore, I figured the disk might've been damaged. So I've launced live Kali linux and scanned it with badblocks ...
0
votes
1answer
84 views

How to determine which partition has badblocks?

I have the following device: Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00MVWB0 Serial Number: WD-WCAZA3607921 LU WWN Device Id: 5 0014ee 2b01eac3e Firmware ...
7
votes
2answers
1k views

Trying to remove/diagnose single Current_Pending_Sector in S.M.A.R.T. data

I'm in a process of doing a fresh Linux install and before I went to do that I thought that it is a good time to verify HDD health since I can safely overwrite any data on the HDD if needed. First ...
0
votes
1answer
95 views

Why Linux works but windows not?

I ran the command badblocks and it found 5 sector errors on my hard drive It is preventing my windows installation from completing. After loading all the files, it is showing a blue screen error. ...
3
votes
0answers
424 views

Reading bad blocks from hard disk too slow in Linux

I'm trying to recover data from an old 320G hard drive (full of bad sectors) to a new one. I found that ddrescue is a good tool for this task due to it's smart algorithm. I have already done this once ...
8
votes
1answer
483 views

Find files affected by bad blocks with md-raid5 and LVM

I've been doing a lot of research on this topic over the last few weeks - and I think I'm close to completing my recovery, as much as is possible at least. To make a long story short, I'll just ...
1
vote
2answers
910 views

Will blocks diagnosed as bad by Linux badblocks command be marked as “bad” in Windows?

I have used badblocks to check for bad blocks, then formatted the disk using the badblocks output through mkdosfs I just want to ask does this make these sectors bad and does Windows 7 just not use ...
1
vote
0answers
919 views

mdadm raid5 read error not correctable

I have a software raid5 setup existing of 4 disks. sda, sdb, sdc, sdd Since everything was up and running I wanted to test the array. To do this I pulled the plug on one of the disks (sdd). Everything ...
0
votes
2answers
99 views

Bad sdcard report 32DB but has only 2GB wired in, how to detect valid area

I bought a while ago a sdcard that is supposedly 32GB, but after using it for some time, I found that it only has 2GB wired in. If I write past the 2GB limit, the files I read are composed of zero ...
2
votes
1answer
795 views

How long will badblocks -vws run?

I'm running badblocks -vws /dev/sda on a new 80GB laptop drive to make sure the disk is good. So far it's completed 2 passes and is working on it's third. How many passes does it normally make?
4
votes
1answer
3k views

How do I determine what file occupies a given sector in Linux?

In Linux, I'd like to know how to find the file(s) if any which as using a particular sector on the hard drive (ext2/3). There is a similar question here regarding Windows, however I need a Linux ...
4
votes
5answers
28k views

External Hard Drive bad sectors recover/mark utility in linux

I've just installed the new version of Ubuntu, Karmic Koala, in my laptop. Everything is fine, except for the fact the system identified about 300 bad sectors in my 1TB external hard drive. I'd like ...