The cisco tag has no wiki summary.
0
votes
0answers
12 views
Cisco IP Phone to SPA3102 to PSTN
I've just picked up a Cisco 7940G and configured it with SIP firmware (8.2). I'd like to use this as my office phone, communicating with POTS/PSTN via a Linksys SPA 3102 VoIP gateway.
In theory, this ...
0
votes
0answers
17 views
Configuring Cisco Aironet 1200 as a repeater to Billion access point
I have a Billion 7700N adsl/router/access point and I want to extend the coverage of the wifi by adding a Cisco Aironet 1200 series as a repeater. Is it possible? Currently it is configured to be an ...
0
votes
0answers
23 views
Router configuration monitor. [closed]
Looking for a tool to manage/backup switch, router and other network device configurations. I have tried Kiwi Cat tools, Cisco Network Assistant. So far did not like either one of them. I am looking ...
0
votes
1answer
62 views
How to set a 5 char (40 bit) ASCII password for WEP on a Linksys v8 device
I have a Linksys FW v8, and I want to use wireless password "12345" for WEP.
I cant set it up, I just can specify a 64 or 128 bit, I want 40 bit, 5 char long.
Is it possible?
1
vote
2answers
65 views
Cisco Wireless AP - How important is hidden SSID
I'm reading the manual for a Cisco wireless AP and they write:
Most wireless networking devices give you the option of broadcasting
the SSID. While this option may be more convenient, it allows ...
6
votes
2answers
83 views
Why can a network address not be a valid host address?
So... I have studied for CCNA and such and been working with IP networking at the least the past 8 years or so. I have always seen and been told that the network address for a subnet is not a valid ...
0
votes
2answers
129 views
Cisco IPsec versus L2TP/IPsec
I have a VPN service which gives me the option of connecting via PPTP, Cisco IPsec, or L2TP over IPsec. PPTP i know is inferior in terms of security and encryption, but I'm not really sure what the ...
0
votes
1answer
53 views
Can Cisco vpn client .pcf file from a PC be used on a Mac?
i recently switched from a PC to a Mac. I want to know if my previous Cisco VPN client .pcf file installed on my PC can be used on my Mac OS?
1
vote
1answer
54 views
Cisco 7962 cable unpluged with POE
I've got a collection of CISCO 7962 IP Phones powered by POE. On some of them I plug them in to our POE switch and I get an error that the Ethernet cable is unplugged. That strikes me as strange ...
0
votes
1answer
87 views
Could this wireless set up cause this issue?
I have two routers hooked up to a DSL modem. The first is an older Linksys wired router(might be BEFSR41) and the other is a newer Cisco Valet M20. The valet was added on recently to enable WiFi ...
0
votes
0answers
92 views
Cisco Any Connect and Mac OS X 10.6.8
I got a strange thing and since I'm not very confident with a Cisco setup, I'm asking here.
I try to connect to a Cisco VPN network, with their Cisco AnyConnect software. I type the good ...
0
votes
1answer
42 views
Cisco 831 VLAN config
I'm looking for a simple, fast way to configure a Cisco 831 router to
do VLAN untagging. I'd like to do something like this:
PORT 1 (E0) VLAN 1,2,3,4 tagged
PORT 2-4 (E0) VLAN 2,3,4 ...
0
votes
1answer
79 views
Create site-to-site VPN from linux to Cisco - possible?
I have a question that I have not found a definitive answer on, but am hoping someone here can chime in and either point me in the right direction or crush my hopes and dreams.
I have a Cisco ASA ...
0
votes
1answer
76 views
Explain a simple network diagram?
In the image below, are bridge1, bdidge2 and bridge3 connected to each other? and how?
i tried to design this in Cisco packet tracer and i used a hub to connect the three bridges? is that right?
0
votes
1answer
107 views
How to share printer across two VLANS on Cisco WRVS4400N?
As the title says, we have two VLANs at the office, one for authorized users and one for guests. The first VLAN contains some resources that should be only for authorized users, but the printer should ...
0
votes
0answers
58 views
Cisco Web VPN: how to run RDP with remoteapplicationcmdline parameter?
I have a Cisco router configured to allow Web VPN Access. It's a great tool - the only thing I can't get to work is to launch an RDP application automatically and not show "remote" desktop at all.
I ...
0
votes
1answer
102 views
WiFi network speed. No difference in wireless N and wireless G networks
I have a Cisco E3200 Wireless N dual band router and external drive with USB2 support attached to it. The drive is shared across my network. My laptop has G WiFi adapter, so it can connect with 54Mbps ...
5
votes
3answers
770 views
Does it make sense to keep different SSIDs for 2.4GHz and 5GHz wireless networks?
My router can have different SSIDs for 2.4 and 5 GHz and I'm not sure if it's better to have the same SSID or not.
Initially I put the same network but I got confused when the MacBook Pro displayed ...
1
vote
2answers
82 views
What processor does the Cisco SRP500 Series router use
Can someone tell me which processor is used in the Cisco SRP 500 series routers, specifically the SRP547w?
I've been trawling Google, the Cisco website and documentation but can't seem to find any ...
0
votes
1answer
195 views
HTTP SSL VPN Client? (alternative to Cisco's AnyConnect VPN)
Is there any free HTTP SSL VPN clients around, one that can act as an alternative to Cisco's own HTTP SSL VPN client (called AnyConnect)?
The Cisco AnyConnect client has acknowledged problems, with ...
3
votes
2answers
240 views
Cisco Router/Switch with MacBook Pro OSX Lion
What I have:
MacBook Pro with OSX Lion
Very old Cisco Router and Switch
Two Crossover Cables (1 Cisco Console to Serial and 1 Cisco Console to Cisco Console)
One Serial to USB Cable
I am very new ...
0
votes
1answer
85 views
What is 10G? Is my switch 10G?
What is 10Gactually ? I have a Cisco switch ( http://www.cisco.com/en/US/products/ps10898/prod_models_comparison.html)
And it has 2xSFP interface and 10 x 10Base-T/100Base-TX/1000Base-T.
...
1
vote
1answer
241 views
Reset gargoyle router to default
I have a Linksys WRT54GL router with gargoyle installed.
Unfortunately, I've forgotten my password so now I'm trying to reset it. I've already tried the 30/30/30 hard reset method, but it didn't ...
0
votes
0answers
76 views
ip-up does not trigger when using built-in cisco vpn on mac osx lion
I am using Cisco VPN client over lion and I want to make the ip-up and ip-down work.
There is no sign of any action taken when I connect or disconnect this VPN connection. I really doubt whether the ...
0
votes
0answers
46 views
How to setup guest wireless network?
I got Cisco 1131 Access Point and a switch that is capable of doing VLANs.
How can I configure the Cisco 1131 Access Point to have 2 wireless SSID, one for office use and one for guests?
getting CLI ...
2
votes
0answers
207 views
AnyConnect SSL VPN Connected but unable to ping my inside LAN
I am trying to configure Anyconnect SSL VPN and it is killing me, I am able to connect to the VPN on a laptop, witch is able to download the anyconnect client from the ASA and I can also connect to ...
0
votes
2answers
41 views
Using MAC address prefix AB:CD:EF
I'm trying to use tcprewrite to change the source MAC address of some packets. I deliberately chose the prefix AB:CD:EF that does not belong to any hardware manufacturer so that I can distinguish such ...
0
votes
1answer
104 views
Setting 3 routers with GNS3
I have three routers in GNS3, each router connected to first router forming like this, /\
I am using class B address 142.55.0.0 with subnet mask 255.255.255.0 to configure the network.
Moreover, I ...
0
votes
0answers
44 views
Linksys E1000 can't connect to linksys CM100
Every time the router loses power ( like I move it, we lose power to the house, etc). It takes many many hours of factory resets and screwing with the cisco tools to get it to find the CM100 on the ...
0
votes
1answer
43 views
After auto secure no RIP updates sent
I was configuring/testing a Cisco router (sorry, I don't know the model since I was using NETLAB), and I had RIPv2 updates propagating/updating correctly. I then used the auto secure command to harden ...
2
votes
0answers
72 views
How can I save / auto-fill a IPSec VPN connection password and user name?
I have set up a Cisco IPSec VPN connection instead of using the Cisco client on Mac OS X. I like it fairly well, it just sits in the tray next to the clock and allows me to easily connect and ...
1
vote
1answer
120 views
How to set up a home SIP Server/Proxy for multi ring?
I have a sip account which only allows one device to be registered. When i'm at home I want incoming calls to be able to ring on multiple devices. All of these devices are connected to the local ...
0
votes
1answer
129 views
Packet tracer IGRP configuration
I am using packet tracer 5.3 version and I am trying to configure IGRP on it but it doesn't show me igrp under routing protocol selection.Router number is 2621XM.IOS version is 12.2.
...
0
votes
1answer
139 views
Cisco switch Link status Up, Protocol down
I just bought a Cisco 3750X switch and when I did a sh ip int brief command, I see that my TE1/1/1 interface (it's a 10G port) has status up but protocol down.
Right now, this 10G port is connected ...
1
vote
1answer
246 views
What is the purpose of a routing protocol? [closed]
I'm studying for CCNA 2 exam. Here's one of the questions. I already know the answer. What I am looking for is the reason why the incorrect answers are...incorrect. =)
For example, the question is:
...
2
votes
1answer
815 views
Use an Asus Transformer Tablet with Cisco VPN Connections [closed]
Our company has recently bought an Asus Transformer Tablet, running Android 3 (Honeycomb). I have been tinkering around with it for a while now and have so far failed badly to get this tablet to ...
0
votes
0answers
89 views
Can I bypass the Cisco ASA portal?
Does anyone know how to bypass the Cisco ASA portal page (clientless SSL VPN), so I can access some internal machine directly from outside using a certain group policy? (or otherwise, be creative)
...
0
votes
1answer
182 views
iptables + vpnc + Cisco IP Phone 7941
I have a Linux gateway with kernel 2.6.39 connected to a Cisco ASA 5500 with vpnc. I'm using iptables with masquerading and forwarding to give the LAN access to the tun0 device connected to the VPN.
...
1
vote
1answer
462 views
How can I get Bonjour to work over my wireless network?
I have a wireless network setup using a AP541N Cisco wireless access point. I can connect to shares from Finder with cmd+K over AFP and SMB to the NAS and I can get to the internet, but thats it. None ...
0
votes
1answer
97 views
What Is “Cisco Compatible eXtensions”?
I have found this in my wireless network card's properties in connection. What is this? Should i enable it?
1
vote
1answer
144 views
Home network setup - incorporating Cisco ASA 5505
I am planning to imlpement an ASA 5505 in my home network and I am wondering if this is a valid configuration. I am wondering if it is necessary to have 3 separate internal subnets or if these can be ...
0
votes
1answer
42 views
Not able to answer call
Got a Cisco Sipura SPA 941 hardware phone and I am connected to Asterix (most likely) VoIP server of my provider.
I am behind a firewall (ADSL) and I have put my phone to the DMZ zone, so it should ...
0
votes
2answers
219 views
Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets
At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between:
A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running ...
1
vote
1answer
689 views
How to configure ShrewSoft VPN to connect to Cisco VPN Server?
What are the steps to connect to a Cisco VPN server using the ShrewSoft VPN Client?
It's important to note that there are different kinds of Cisco VPN connections:
Cisco VPN with pre-shared key ...
0
votes
0answers
143 views
Is Cisco VPN an implementation of a standard VPN protocol?
Is the Cisco VPN an implementation of some standard protocol?
I know that the ShrewSoft VPN client is able to connect to a Cisco VPN server (I know this because I use it - to bypass the Disallow ...
2
votes
1answer
324 views
NAS storage slow network speed (D-Link DNS 323)
i set-up the D-LINK DNS 323 NAS unit with RAID 1 (dual 2-terabyte 5400 rpm drives)
it works, but it is slow in copying files between my computer and it (8 minutes to copy 4.5 gig file between NAS and ...
0
votes
0answers
750 views
How to connect site to site from Linux IPsec VPN through a Juniper Junos SRX (210, 240 series) gateway?
It's been almost more than a week, but I seem to have no answer for this and can't really figure out how to solve this:
I am using Fedora/CentOS Linux and have a Juniper SRX210 gateway configured as ...
0
votes
0answers
121 views
Shared secret length limit on OSX VPN client
I'm trying to setup the built-in VPN client with OS X.
The settings I'm using (IPsec GW, shared secret, etc...) work flawlessly using other clients (IPsecuritas, vpnc, etc...) but isn't working with ...
0
votes
0answers
50 views
How to view files of server with Cisco VPN Client
I am able to connect site to Cisco VPN Client Version 5.0.07.0414 with username and password provided, but no idea how to work and view files of server. Your help would be appreciated.
Thanks
6
votes
3answers
3k views
How to allow local LAN access while connected to Cisco VPN?
How can I maintain local LAN access while connected to Cisco VPN?
When connecting using Cisco VPN, the server has to ability to instruct the client to prevent local LAN access.
Assuming this ...
