0
votes
0answers
160 views

Cisco AnyConnect client removes default gateway after disconnect, but only on Intel Ethernet Adapter not on wireless connection

I recently installed Intel Gigabit CT Network Adapter on my Windows 7 64-bit machine. Previously, I was using wireless connection and Cisco AnyConnect VPN client ver 3.1.0165. When trying connect to ...
0
votes
1answer
62 views

Cannot route traffic between 2 networks

>C:\>netstat -r IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface ...
5
votes
1answer
950 views

Understanding Windows Routing Tables and Default Gateways

long-time reader, first-time poster! First, let me thank you all for reading this post, and for having such great answers to everyone's questions. I think this is the only time I've had to post ...
0
votes
2answers
1k views

Default gateway 0.0.0.0 on-link

My laptop's NIC went bad and I had to start using a USB Ethernet adapter. When I start up the computer, or even simply unplug and plug in the adapter, it gets two default gateways which show up in ...
0
votes
0answers
85 views

Adding an IP block into VMWare Esxi

I have a dedicated server with VMWare Exsi 5.5 installed and I have recently bought another /29 from my colo provider. They have set things up so that it works this way: Original: Network: 1.2.3.1 ...
0
votes
1answer
90 views

Why can I only view certain devices if I am using the 192.168.2.1 gateway

I have a kind of weird problem. Every device we have at work printers, servers, etc. Exist on the 192.168.1.0 network. We have some remote devices that are an extension of our network and they ...
0
votes
1answer
242 views

Debian based server picks wrong network as gateway

I'm configuring own server to act as router. It has three interfaces, two cable and wifi. Following this article to configure access point. After setting bridge i have problem with default gateway. ...
0
votes
0answers
79 views

How does UPnP know which IGD to port forward on if there is more than one IGD?

Say I have two IGDs on the same subnet with UPnP enabled. The host is configured to use one as its default gateway. How do UPnP applications know which IGD to port forward on. I don't think they use ...
0
votes
1answer
757 views

1 Public Facing NIC and 1 Private Facing NIC - Different Subnets and Different Default Gateways

I have tried many approaches to my problem. I had gotten his to work using static routes. But, I wanted a RAID 0 setup so I wiped and installed a clean minimal Centos 6.4 system. Current: Centos ...
0
votes
1answer
68 views

What does gateway mean in linux route table?

Does it mean the next hop of the route? Can the gateway be the next next hop, if there is an internal router in the private network?
1
vote
0answers
337 views

iproute nexthop not working - defining multiple default gateways

I have several point to point connections and I'd like to use all of them as default gateways. I saw this link which explains how to do this using load balancing by calling ip route with a nexthop ...
0
votes
1answer
250 views

How to get the gateway for a specific route on command line in Windows?

Is there a way to print out the gateway for a specific route (not interface) in Windows (in this case Win7)? I'd need to add a route dynamically in an OpenVPN _up script, but since the gateway is ...
2
votes
3answers
222 views

Redirect unregistered users to the site on local machine

I have a server 192.168.0.3 (SERVER). Running Ubuntu Server + DHCP server + Apache; The router 192.168.0.1 (ROUTER) (I haven't access to it); I have a web-application on SERVER for registration users ...
1
vote
0answers
229 views

Weird routing issue [closed]

I just updated the route tables due to a mistake on my part. I am working on getting networking working correctly on a cluster of 14 virtual servers at a customer site. 11 of them work fine for ...
1
vote
2answers
3k views

Linux route add between static LAN and Wifi Gateway

I have two local machines connected to each other via wired ethernet and one of those machines is also connected to a wifi network which provides internet access. A pseudo-graphical representation ...
0
votes
1answer
47 views

NetID set as the Gateway for a route

After establishing a pptp VPN connection I checked out the routing table and found out that there are two default routes first one defined on the eth0 interface and the other on defined on ppp0 ... ...
0
votes
0answers
325 views

Redundant default gateways on LAN

I have two default gateways in my network: 192.168.1.1 and 192.168.1.2. Is there a way to make Windows clients to detect the dead gateway and chnage over to the wowrking one automatically? My gateways ...
0
votes
0answers
408 views

Is there a way to make PC running Windows 7 forward packets via the same interface on which they arrived?

I'm testing a NEWT configuration to be used for an Internet simulation between 16 peers. The NEWT host will be running on a dedicated PC as opposed to one of the peers, and all peers and the NEWT host ...
1
vote
1answer
2k views

Using VPN connection in OSX will only route through the first service in “Service Order”

I am trying to get my VPN connection to only route network traffic related to my workplace through the VPN connection and any other traffic through my Wi-Fi connection. If I have my Wi-Fi at the top ...
0
votes
1answer
640 views

Can't route into WAN with IPCop Router

i try to setup a IPCOP Router but i can't access the WAN from LAN but the LAN from WAN works fine. Example: WAN IP from IPCOP 192.168.1.130/26 WAN IP aliase from IPCOP 192.168.1.131 ... 190 /26 WAN ...
2
votes
3answers
140 views

Is there a way to tell my modem/packets to go to a gateway other than that of my ISP?

My attempts to get onto www.radioshack.com come up with a 'Network Connectivity' error in the browser (both SeaMonkey, and Chrome). tracert got as far as my National Internet Backbone ...
6
votes
3answers
3k views

SSH server can't be connected to when VPN is turned on

I recently found that when my workstation connects through a VPN connection then its SSH server can't be connected to from a remote site. I am sure it's a routing problem because the the VPN client ...
1
vote
1answer
387 views

Why is 192.168.1.0 needed in route table?

My home network is configured as follows: Computer -- Route -- Internet If I run route on my computer, I see ~ route -n Kernel IP routing table Destination Gateway Genmask ...
13
votes
4answers
9k views

How can I ping via an alternate gateway?

Our network has two modems, each one hidden behind a router. The primary router is on 10.1.1.1, the backup router is on 10.1.1.2, and are both configured to the 10.1.1.0/24 subnet. Both routers have ...
1
vote
2answers
2k views

I don't want my DHCP to be a default gateway

I have a device which runs a DHCP server. When I connect it with USB to my computer, the PC gets an IP address and the device becomes the default gateway. I just want the device to agree on IP ...
3
votes
2answers
1k views

Why does `route` hang for a while before the route table being dumped?

Typing the command: % route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 2 0 ...
3
votes
2answers
1k views

2 gateways 1 nic Ubuntu

Please note that this is ONE NIC and TWO Gateways Now this solution is super easy in Windows: * Connection Properties -> TCP/IP Properties -> Default Gateways -> Add (separated by metrics) I notice ...
3
votes
1answer
1k views

Linux: multiple network connections - 3G/4G / Wifi / LAN / etc; how can i set a preferred network connection to use?

I've been looking at how I can setup a laptop that has multiple network interfaces, but a problem exists if all the connections are active, i.e. 3G, WiFi and LAN are all connected, I would like it to ...
5
votes
3answers
690 views

Multiple home routers

Suppose I have the following configuration: Router A: WAN port connected to the Internet, LAN = 192.168.1.0/24 Computer A: Connected to router A as 192.168.1.101 Router B: WAN port connected to ...