0
votes
1answer
38 views

A desktop PC connected to two network interfaces - what does that mean?

I am to create a network design draft where each PC is connected to two network interfaces. Well, what does it mean? That it could use network printer?
2
votes
2answers
65 views

Is it possible to use the interface on a remote machine which I can SSH into?

I can SSH into a machine which has a wifi adapter connected, with interface wlan0. Can I use its interface (wlan0) on my client machine ? As an example, if I want to run iwconfig (or any tool which ...
0
votes
1answer
91 views

CE interface in Solaris 10 drops mac address (per ifconfig)

I recently installed Solaris 10 1/13 and proprietary TCP PEP software on a new hard drive within an old Sun v210. When the PEP software starts, the Sun's CE0 interface loses its "ether" address, ...
0
votes
1answer
718 views

How to find out total NIC cards and total available physical ports in linux

I need to find out how many total physical ports my server has, and how many of them are in use and how many free. Can you kindly help how to find it: This is what i find from dmidecode output: ...
1
vote
1answer
56 views

Linux does not communicate to Windows subinterface

I set my NIC on Windows so that I have two interfaces: one (the first one) has IP 192.168.0.5 the other one has IP 10.10.10.1. On a Linux machine I set an interface to 10.10.10.2. On another Linux ...
0
votes
1answer
450 views

setting up wifi for static ip on ubuntu 12.04

I want to setup dhcp and static IP I have 2 lan card, Ubuntu 12.04 and it is a laptop the wireless interface I want to give a static IP and lan to have a dynamic ip how should I go about making ...
1
vote
2answers
3k views

Use commandline to show disabled network interfaces in windows? (Mobile Broadband and Regular Connections)

There are a few ways you can list network interfaces via commandline. For example: netsh interface show interface netsh interface ip show interfaces ipconfig |findstr "adapter" For Mobile Broadband ...
1
vote
1answer
212 views

ubuntu setup network routing table

I have two interfaces: eth0 and wlan0. I want all traffic to go though wlan0 except for port 80 traffic that should go on eth0. Is there a way to setup the routing table so it does that? My current ...
1
vote
0answers
180 views

Bind process to network interface

I'm attempting to perform simultaneous bandwidth tests from a single machine using multiple network interfaces. None of the utilities I've found so far allow me to do this. The closest was iperf ...
1
vote
1answer
1k views

Debian: Routing Table and Two Interfaces

I've a Debian machine with this network scenario: eth0 - Internet Connection via local Router (172.20.1.x) ppp0 - Dial-up to a network without internet (10.x.x.x) I've set pppd so it won't add ...
0
votes
1answer
233 views

Tunneling a particular site through a VPN on a particular NIC

I have two NICs on my desktop — an Ethernet interface and a WiFi interface. I have a VPN connection that allows me to connect to American servers which i use to access sites like Pandora. I can ...
1
vote
1answer
531 views

Configuring two interfaces with netcfg in VM (VirtualBox)

I am using netcfg to configure two interfaces in my archlinux VM. In VirtualBox I have set two active interfaces. The first (eth0) is the NAT interface to provide the VM with Internet access. The ...
1
vote
2answers
232 views

What does `ec` mean in `HWaddr ec`?

When I do ifconfig on my laptop I get HWaddr ec and than an address, this is next to eth0. Note that my IPv4 address only appears next to eth1 so I assume my laptop uses the eth1 network interface. I ...
3
votes
4answers
272 views

Three computers accessing internet but only two network interfaces showing in ´ifconfig´, why?

My gateway(router) is connected to DSL. The gateway connects to 1 wireless transceiver device. 2 fixed computers connect to the router. At the moment of me doing ifconfig 2 fixed computers were ...
2
votes
1answer
276 views

Specific Network Interface

What I'd like to do is to force an instance of a browser to use a specific Network Interface. I've tried: http://www.r1ch.net/stuff/forcebindip/ and was less than successful - besides, I'd like to ...
2
votes
1answer
257 views

Alternate traffic through multiple interfaces on Linux

I have a VPS with three IP's. I am trying to setup the network configuration to allow round robin usage of the three IP's for outgoing requests (downloads into VPS). How do I change the following ...
0
votes
1answer
1k views

Configuring IPv6 automatically and IPv4 statically

I've got a Ubuntu Linux box that has two IPv4 addresses and an IPv6 address. This is my current /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 eth0:0 iface eth0 inet static ...