1
vote
0answers
34 views

Block WiFi Access Point by MAC address on DD-WRT using client mode WAN connection

My router's WAN connection is configured to connect to a subscription based public WiFi network. I've determined the public network has three different access points in range of my router (all using ...
0
votes
0answers
15 views

dd-wrt disabled DHCP, now no longer connects even wired

I had a perfectly functional DD-WRT router set up with networked file storage, port forwarding, multiple wireless networks, etc. The router was connected directly to my modem. I moved to a new ...
0
votes
1answer
29 views

Can access router settings via Wifi but not on a wired connection

On my Netgear WNR2000v3 running DD-WRT I can access the setting panel via Wifi but not on a wired connection why is this? I need it to connect to ethernet to flash the default firmware back via TFTP.
0
votes
0answers
18 views

multiple DHCP servers for wireless users on same subnet

I am trying to set up 2 router in our network with following set up. 2 routers, 1 is the main router that DHCP is enabled to assign ip to all wired PCs, the other one can be assumed for guest, which ...
0
votes
2answers
29 views

DD-WRT and 2 virtual interfaces with each dedicated to N or G

Can virtual interfaces be setup with DD-WRT to be dedicated to a specific protocol? I have a Wireless G printer and I've noticed that when my router is set to "compatibility mode" my throughput tanks. ...
1
vote
3answers
42 views

How to connect 2 Routers to share files but not internet?

I've looked everywhere for how to do this but I can't really find a full answer. My neighbor and I share a lot of files between each other, Videos, Music, game saves, etc. What I'd like to do is be ...
0
votes
1answer
22 views

How do I connect to the internet from a dd-wrt router plugged into a modem-router combination?

I've got a cable modem (A) which is also a wireless router and a dd-wrt wireless router (B). I've connected (B)'s "internet" port to one of (A)'s local ports. I can connect to (B) over the air just ...
0
votes
0answers
69 views

DD-WRT / Ubuntu DHCP / SQUID Transparent Proxy

Trying to segregate WLAN clients based on VLAN SSID, but I can't use multiple ports on DD-WRT router. AP is on second floor with only one drop going to basement where my SQUID/DHCPD server is. If I ...
0
votes
1answer
63 views

How to make DD-WRT router's (configured like a repeater) devices be accessible on LAN? (i.e. integrate DHCP for both routers)

I have a D-Link DIR-600-A1 router running DD-WRT (using the 601's firmware: except for the model number, they are near identical). It has an Atheros chip, so there is no "repeater" option. You can ...
0
votes
0answers
26 views

E3000 as repeater (bridge?) for Motorola DOCSIS cable modem

I'm trying to use my E3000 as a bridge/repeater to extend the range of my cable modem (Motorola DOCSIS 3.0). To that end, I flashed it with DD-WRT firmware. I'm not clear if I want "Repeater" or ...
0
votes
0answers
49 views

DD-WRT (Linksys) slow local file transfer over WiFi

I have the following setup - a modem/router... it is a device that converts fibreoptic to standard LAN. Then I have my main router/DHCP server/ WiFi. I use another router with DD-WRT as an accesspoint ...
0
votes
0answers
13 views

forward all client traffic on one network through a router on another network on a secure port

good day all after much research, and hastle, I have had no luck in finding a solution to this issue I have in mind to create a "VPN" for Windows clients: Forward all client traffic to a router on ...
0
votes
1answer
205 views

What is an antenna chain and how do I figure out the correct setting for my router?

Information on antenna chains has been difficult to find, (google seems to think I want to search for antenna gain). I found this IEEE article which defines what they are, but it doesn't explain how ...
-4
votes
2answers
75 views

A “home server” to “control” other PCs [closed]

I might be asking a lot from the title so let me clarify. I'm an I.T System Administrator. I understand Client-Server relationship fully. I use Windows GPO on our server for almost every use Windows ...
2
votes
1answer
99 views

DD Wrt Wifi bridge connection breaking

I have a DD Wrt connected to a DD Wrt router as a Router - Client bridge setup. It works fine for sometime, but occasionally, it appears to stop communicating to the router, or internet.. not sure. ...
4
votes
1answer
178 views

How to connect (via DD-WRT) to a device known by its MAC address?

This question might seem odd at first, because the answer may look trivial: "Either assign a static IP address to it or just DHCP it." Well... this challenge turns out to be not so simple: The ...
1
vote
0answers
40 views

Linking router from VPN to main network?

So, here's what I have going on now: Thomson Cable Modem ---> WAN port on D-Link N600 (IP 192.168.0.1 - DHCP 192.168.0.100-149) running stock D-link Firmware ---> Wan port on Linksys E1200 (IP ...
2
votes
1answer
38 views

How to isolate open guest AP from uplinked private AP with dd-wrt

I have two routers, setup like so: [MODEM] | [WAN] <<< +-----------------------------+ <<<< | WRT54GL with stock firmware ...
1
vote
1answer
68 views

Will the dd-wrt Big build run on my Linksys WRT54GL?

I have a Linksys WRT54GL access point acting as a NAT router, with the inside network being my house's wireless and the outside network being a point-to-point link to my DSL gateway. My ISP is Telmex ...
-2
votes
1answer
76 views

How to host a website on a wifi-router and a USB drive? [duplicate]

I have a TP-Link MR-3020 Router with a USB port. What I want to do is to setup a website on my USB flash drive, which will be connected to the router via the USB port. Now, when anybody is connected ...
0
votes
0answers
36 views

Bridged VLAN and VAC can't connect to the internet on DD-WRT

I just recieved my new Netgear Nighthawk AC router, and I installed the latest DD-WRT from myopenrouter.com (build 23720). I am trying to create a VLAN bridged with a Virtual Access Point (VAC) so ...
0
votes
0answers
122 views

dd-wrt Displaing low signal quality

I have installed dd-wrt firmware on tp-linkwr-740N router. And have following wireless settings, and the in dd-wrt status panel, it displays following signal quality even if the laptop is just 7 ...
0
votes
0answers
164 views

How to configure a dd-wrt router between a cable modem and main router to run all clients through a VPN service?

Was told by a http://networkengineering.stackexchange.com moderator to post this here so hoping it's the right place... Currently I have a DD-WRT router with VPN capabilities. I have a Motorola ...
1
vote
2answers
89 views

Anyone familiar with dd-wrt scripting?

My router will randomly lose connection to everything. I can't ping it, it has no internet, I can't even get to the setup page through a wired connection. It won't fix until I unplug it and plug it ...
0
votes
2answers
205 views

Why is my D-Link IP webcam unreachable from within the LAN, but accessible from outside?

I recently bought a D-Link DCS-930L network webcam which is connected to my WLAN network. It retrieves a IP address via DHCP from DD-WRT based router (a TP-Link TL-WR1043ND), and it is listed under ...
1
vote
4answers
661 views

Why can't I install DD-WRT on a DLINK DIR 600 A1?

I have an old router laying around and I am wanting to install DD-WRT on it to make it an access point. However, when downloading it I get an error: The uploaded firmware file may not be correct. ...
0
votes
1answer
35 views

Is it possible to turn off NAT on some cheap wireless router?

http://amzn.com/B001FWYGJS I have several TP-Link and other brands' wireless router like that in above amazon link. They seem in common to default to not allow user to turn off NAT when I want to ...
1
vote
1answer
59 views

Deny Connections between WiFi Clients

I read somewhere that it would be a good idea to deny connections between clients of my open WiFi to improve performance of the whole WiFi. Where do I look to configure this on DD-WRT? (It is a ...
0
votes
1answer
192 views

DD-WRT: How To Do Multiple APs on Wired Network?

I've been following the page on the DD-WRT web page for linking routers as WAP's (wireless access points, both connected through a wired connection) [1], and I'm finding the following issues: I ...
0
votes
0answers
41 views

Laptop behind cascaded router can't ping server

My network is set up thusly: DD-WRT is connected via wire to DD-NETGEAR LAN-to-LAN. My problem is the laptop can't talk to the server and vice versa. Both machines can talk to everything else (via ...
0
votes
1answer
68 views

Constantly Losing Internet Connection 2Wire HGV3801

It seems like I will continuously lose my internet connection every 5-15 minutes for about 10-20 seconds. Very annoying. I have AT&T U-Verse coming through the 2Wire HGV3801. The wireless ...
0
votes
0answers
148 views

Reliable Connection PPTP VPN to DD-WRT Router

I have set up a PPTP server connection so I can connect to a DD-WRT router remotely. I have set up the connection on my computer by using the "Connect to a Workplace" feature in Windows 8. I was ...
0
votes
0answers
105 views

How to connect a WiFi router to multiple networks simultaneously?

I am trying to find a solution that will allow my router to connect to four Wi-Fi networks at the same time. I and two neighbors each have mobile broadband Internet, we each use a simple router to ...
0
votes
1answer
45 views

Why are my DD-WRT Repeaters connecting to each other instead of the access point?

I have a few LinkSys WRT54GL routers repeating off a main access point. I'm struggling to keep the wifi consistent though. It seems like some of my repeaters are connecting to each other instead of ...
1
vote
1answer
394 views

How to fix Wrong firmware installed on router

I have a Netgear WNR2000v3 (n300) router. The guy who came in and installed it for me somehow installed the Netgear RP614v4 Firmware on it. I have been having severe connectivity problems, and cannot ...
1
vote
2answers
75 views

WiFi experiences severe delay when more than one user is using the internet

Recently got fibre internet, 40/2, works fine when on one PC. If two access it at once, even if one is only on Google images and not even watching 1080p streams it lags horribly (5.5k+ ping). I don't ...
0
votes
0answers
139 views

Hardware setup for adding a dd-wrt/WRT54G to monitor DSL/Internet bandwidth

While looking at another question/answer at: How can I monitor network traffic? and because I do not have enough points to comment I want to follow this up with another question: I too am looking to ...
0
votes
0answers
158 views

How to make a sky sagem 2504 act as a wireless bridge?

I've got a Sagem 2504 from sky, however I've changed my ISP and I'm now using a different router. I would like to get the Sagem 2504 to connect with my current router via Wi-Fi to then connect with ...
3
votes
2answers
447 views

How can I monitor network traffic?

I need to collect network traffic statistics so that if questions come up about how much traffic I'm using I have the answer independent of my ISP. I have a home network with about 10 devices ...
0
votes
1answer
176 views

DD-WRT Acces Point as a Router

Following suggestion to this question asked on Network Engineering, I am asking the question here. this is an extension to my previous question (I think it was deleted), where I was claiming that ...
2
votes
1answer
3k views

How to set up Asus RT-N66U in bridge mode with wired connection to main router?

I have a wired router (TP-Link RT-860) in the basement where the cable service comes in. Eight wired ethernet connections span two buildings. I currently have a Linksys wireless router set up in ...
0
votes
2answers
111 views

How to get tomato-like features on modern wifi hub?

I used to run tomato (shibby) on an asus wifi router, and it was great. I could: -- Run scripts on a schedule to modify iptables (e.g. block facebook at certain hours) -- Regulate bandwidth on a per ...
1
vote
0answers
750 views

Why won't FreeRadius allow WPA2 Enterprise/PEAP Wi-Fi connections?

First a bit of background: I've been tinkering with this on and off for a few days and it's getting frustrating. I've got a NetGear r6300 loaded up with DD-WRT v24/SP2 Giga and I've configured SSH to ...
1
vote
0answers
142 views

ddwrt port forwarding with wireless access points behind a wireless client

I've tried port forwarding to a wifi device that's connected through 2 routers: Wifi Device (192.168.0.200) -> Wireless Access Point (DD-WRT, 192.168.0.2) -> Wire Connection to Router 1 (running ...
0
votes
1answer
1k views

Back to original firmware on TP Link WR2543ND

I flashed firmware on my WR2543ND router according to these instructions. But my router no longer creates wifi, wired LAN cables don't work anymore and 95% of time I cannot even access that router on ...
1
vote
0answers
319 views

Using a WRT54G V8 as a repeater and print server?

I currently have an old WRT54G V8 setup with my printer (HP Laserjet 400M 401DN) to broadcast it's own wireless network (no internet, just printer). The printer works wirelessly with this setup but I ...
1
vote
0answers
356 views

How do I set up wireless radio time restriction in DD-WRT build 21061?

I upgraded to D-WRT specifically to get the ability to restrict wireless access on a schedule. I'm using a Netgear WNDR3700, and the install went flawlessly (as far as I can determine), but there is ...
1
vote
1answer
1k views

Dualband Routers with the same SSID? [duplicate]

I have recently purchased two Buffalo AirStation N600 Dualband routers and have set one up to be the main router and the other as a wireless access point. Both are running open source DD-WRT firmware ...
1
vote
2answers
739 views

Routers will not cascade

I'm attempting to cascade two routers to extend my wireless network, using a Linksys E1200 as a master and a Linksys E1500 as a slave. The E1200 is running the stock firmware but the E1500 is running ...
1
vote
2answers
2k views

DD-WRT and Chromecast: default WLAN to LAN bridge blocks UDP?

I have DD-WRT running in gateway mode on a DIR-615 I1. I've updated to the newest available build. Chromecast is a wireless-only device, for those unfamiliar. The device has been set up and ...