0
votes
0answers
20 views

How to properly cascade a Netgear router (using Tomato) with the ISP router/modem (Orange Livebox)?

I've been using my ISP's modem/router which is an Orange Livebox for the past. I now bought a Netgear WNR3500lv2 and installed Tomato (similar to DD-WRT) in order to have more configuration options ...
0
votes
0answers
18 views

Why is there high packet loss when transferring across wireless network?

Normal internet browsing behavior does not trigger packet loss, but when I am doing a significant, sustained wireless to wireless transfers[0], packet loss increases to 30-50%. Wired devices are ...
0
votes
2answers
42 views

Can a consumer wireless router act as both a wireless client and access point?

I'm going to be moving in the future, and integrating my home network into that of my landlord. I wish to maintain an isolated network while using his internet connection, so I'm planning on cascading ...
0
votes
0answers
29 views

devices won't connect to bridge router

I've set up a bridge router with Tomato (by Shibby) firmware following this instruction here. Basically I set my bridge router to a different IP but the same SSID and pwd as the host router (from ...
0
votes
0answers
62 views

Are public IPs in my Tomato router device list something to worry about?

My ISP was recently bought out (O2 by Sky UK) and I have been forced from PPPoE to PPPoA. I've set up a a PPPoA relay using a function on an old TP-Link router I had called "PPP IP Extension", which ...
3
votes
1answer
214 views

Computer no longer connecting wirelessly to router after Tomato clean install

I just installed Tomato firmware (details below) on my wireless-N router and everything appears to be working fine on the router's end. I can connect to the Internet properly with a wired (Ethernet) ...
0
votes
0answers
215 views

Why did my router randomly assign wireless devices to br0 interface?

So I have a WRT54GL router with Tomato firmware on. I have few wireless devices on my network. Most of the time they work fine, but occasionally, some devices that were previously on router's eth1 ...
3
votes
7answers
7k views

Very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ...
0
votes
1answer
193 views

Is an older router (b/g only) that supports DD-WRT or Tomato better than a new n supporting device?

I'm currently looking for a new router as my current one is dying and insecure. One of it's major problems is that it stopped getting updates from the manufacturer and doesn't support WPA2. Of the two ...
0
votes
1answer
451 views

adsl modem/router with “ssh” server

Any recommendation re a good ADSL 2+ modem/router for home that has support for running an SSH server? Would ideally want the ssh support to include: custom port can be defined (not standard ssh ...
0
votes
1answer
198 views

How can I choose the rights firmware of Tomato when I do not have access to the router?

I have an old router running an old version of Tomato and I want to upgrade it. The problem is that on the web interface it reports a generic version: WRT54G/WRT54GS/WRT54GL but the latest tomato ...
3
votes
3answers
2k views

Why do I get periodic dips in the wireless speeds?

I am using a Netgear WNR3500L router to share my internet connection via WiFi to my home computers. My trouble is that I get periodic dips in wireless speeds every 120 seconds (almost exactly every ...
2
votes
1answer
270 views

Tomato Firmware & TC-ATM Patch

I have a router with the tomato speedmod patches applied (Viktek mod) and this is connected to an ADSL modem. How do I use the tc-atm patch? ...
1
vote
2answers
2k views

How to reboot Tomato router remotely?

I can't access my Tomato router remotely (normally I could login through SSH), but I can access the computers on my home network, so it's operating and I can go through it to them. But they can't ...