3

I have a self-built FreeNAS system, which uses 4 HDD in one ZFS pool purely for storage, and 2 mirrored 16GB USB memory sticks in a ZFS mirror for booting from. It is stable and has been running for around 8 months. However, the overnight emails are usually along these lines:

Checking status of zfs pools:
 NAME           SIZE  ALLOC   FREE  EXPANDSZ   FRAG    CAP  DEDUP  HEALTH  ALTROOT
 freenas-boot  14.5G  1.67G  12.8G         -      -    11%  1.00x  ONLINE  -
 volume1       7.25T   457G  6.80T         -     2%     6%  1.00x  ONLINE  /mnt



  pool: freenas-boot
 state: ONLINE
status: One or more devices has experienced an unrecoverable error.  An
        attempt was made to correct the error.  Applications are unaffected.
action: Determine if the device needs to be replaced, and clear the errors
        using 'zpool clear' or replace the device with 'zpool replace'.
   see: http://illumos.org/msg/ZFS-8000-9P
  scan: scrub repaired 232K in 0h6m with 0 errors on Sun Oct 23 03:51:22 2016
config:



   NAME                                            STATE     READ WRITE CKSUM
   freenas-boot                                    ONLINE       0     0     0
     mirror-0                                      ONLINE       0     0     0
       gptid/253f05a3-be26-11e5-8d9c-d05099c04470  ONLINE       0     0     1
       gptid/879584e0-bfb0-11e5-ba20-d05099c04470  ONLINE       0     0     9



errors: No known data errors

The checksum errors will occasionally increase, then when I perform a normal FreeNAS update, will all reset back to 0 again, whereupon the process will repeat, with the checksum errors creeping up now and again.

I've seen nothing to indicate that the HDDs themselves are having any faults, and I download the FreeNAS config to an external backup location when I make changes, so I should be able to reinstall on a new flash drive if necessary.

All that said, how concerned should I be about these checksum errors?

Improve this question
3
  • Relevant: ZFS checksum errors, when do I replace the drive? on Server Fault.
    – user
    Nov 5, 2016 at 14:43
  • Well, based on personal experience, I would say very concerned. Thank to checksum errors, my pool was lost as I was unable to import it.
    – GGGuest
    Apr 28, 2019 at 12:48
  • @GGGuest I’d completely forgotten about this question. After asking it, I tried a different usb memory stick, only to quickly have the same issue. I chose the enclosure and motherboard with future expansion in mind, so had plenty of free space for new internal drives - chucked in a couple of old ones to mirror the USBs, and haven’t looked back since.
    – James Thorpe
    Apr 28, 2019 at 14:31

1 Answer 1

Reset to default
2

Probable causes

These errors can have different sources, some popular include:

  • Flaky connections or damaged cables
  • Sudden power loss or forceful removal of devices
  • Memory errors if using non-ECC RAM that is faulty

You can clear the errors with zpool clear, because the errors were few (instead of too many errors) and they did not affect the same blocks on each device. I suspect the FreeNAS upgrade also does this so it results in the situation you described.

Possible solutions

I would do the following:

  • Run memtest86+ overnight to rule out faults in the memory
  • Disconnect and reconnect all cables, check for lose connections, if needed replace cables (they are cheap, so simply replacing them is quicker than troubleshooting)
  • Try if running with an UPS makes a difference if you live in an area with unstable energy supply (brown-outs are a thing in some parts of the USA, I've read)
  • Test if the USB port/controller is at fault by using a different one, or a PCIe adaptor card (quite cheap)
  • Try to use another type of USB sticks, I've had good experiences with SLC-based USB3 sticks (only checksum errors were on removal or blackout)
Improve this answer

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .