7

How can I disable the blue LED on the bottom of my Acer ED270UP Monitor? I’ve checked the settings but can’t seem to find any option. I also want to avoid using tape. Thanks.

Improve this question
7
  • 4
    I have found something like this does wonders.
    – Ramhound
    Jan 21, 2022 at 17:39
  • 3
    The only option other than tape is opening the monitor and physically disabling the LED. You do not want that.
    – Daniel B
    Jan 21, 2022 at 21:46
  • If you're really set against tape, you could 3D print a cover in the same colour as your monitor. But that's a lot of extra work for a simple problem.
    – Mast
    Jan 22, 2022 at 9:12
  • 3
    I took a quick look at a online manual for your model of monitor and it appears the LED is used as a indicator when troubleshooting a defective monitor. So it appears there is no software based method to disable the LED and your only course of action is to follow one of the many hacks in the answers here.
    – Cave Johnson
    Jan 23, 2022 at 4:31
  • 1
    @DanielB that's clearly not true - black paint is an option I've used on over-bright LEDs, both with and without opening things up
    – Chris H
    Jan 23, 2022 at 16:22

4 Answers 4

Reset to default
27

Put a piece of non-transparent tape on it.

Works on all kinds of hardware!

Improve this answer
6
  • I even have a selection of different coloured tape, for a multitude of otherwise irritating LEDs around the house ;)
    – Tetsujin
    Jan 21, 2022 at 17:42
  • 3
    I've edited my post. I want to avoid using tape, but I appreciate your suggestion nonetheless.
    – Ryder Cragie
    Jan 21, 2022 at 21:47
  • 2
    I'm three feet from five things that have tape over their lights. My 4k ASUS has that option. On an Acer? GL.
    – Mazura
    Jan 22, 2022 at 4:09
  • @Tetsujin do you, like me, sometimes choose tape that will act as a dimmer rather than a complete block?
    – Chris H
    Jan 23, 2022 at 16:23
  • 6
    @ChrisH - Indeed I do. I have some off-white tape which needs probably 5 layers to completely block a bright LED, so usually two or three are used, so I can still see the indicators, without announcing to passing aircraft this might be a good place to land;)
    – Tetsujin
    Jan 23, 2022 at 16:30
12

Color the LED with black permanent marker. The ink will not be completely opaque, but will dramatically reduce the brightness of the LED. Easily wiped off with isopropanol if you dislike the result.

Improve this answer
2
  • Acrylic markers have much better coverage than the usual alcohol-based permanent markers. On the other hand they are more difficult to remove (again isopropanol, ethanol, ammonia etc.) --- I have a good experience with Pilot Pintor markers: pilot-pintor.eu/en-en
    – pabouk - Ukraine stay strong
    Jan 24, 2022 at 9:22
  • The solvent in permanent markers can possibly scar the plastic around the led permanently, though.
    – rackandboneman
    Jan 24, 2022 at 12:22
9

I know you don't want tape. Use a blob of blu-tack. Lead a simple life and save brain cells for the things that matter.

Improve this answer
7

To do this without using tape (or blu-tack etc) you might have to do one of the following ...

  • open the case and

    • cut one leg of the LED using small side-cutters. cutters and LED
    • desolder the LED with a soldering iron and flux and solder-wick desoldering tools
    • crush the LED with needle-nosed pliers crusher

  • get your electric drill out and hope your destruction doesn't penetrate the PCB and that any LED fragments that fall inside are non-conducting or do not land anywhere they will cause a house-enveloping fire.

Frankly a small piece of tape is a better solution. For things where cosmetics matter I sometimes use small round stick-on paper disks of the sort that used to be used on wall-calendars/planning charts

phone with camera covered by round sticker

For really bright LEDs you might need to epoxy on a small disk of aluminium foil cut using a hole punch.

Improve this answer
4
  • 4
    If you're going to use a soldering iron anyway, you could also replace the LED with one of a less obnoxious colour, and/or bodge a series resistor in there to reduce the brightness...
    – marcelm
    Jan 22, 2022 at 15:25
  • 1
    Thanks. I've took the LED out. Much better than covering it in tape!
    – Ryder Cragie
    Jan 22, 2022 at 20:18
  • 6
    @RyderCragie I've took the LED out. Great! page 19 of the manual for you monitor (not sure if it is real or not) (but most of the time these are status LEDs) says that the LED is used for trouble-shooting!
    – NotStanding with GoGotaHome
    Jan 23, 2022 at 14:42
  • 1
    Covering the LED with tape BELOW the cover would have been an option...
    – rackandboneman
    Jan 24, 2022 at 12:23

You must log in to answer this question.

Not the answer you're looking for? Browse other questions tagged .