14

At my workplace we have USB microphones attached to PCs in high traffic areas. We are looking for a lock to put on the USB port so that will hold the mic in place. This doesn't even need to be locked, just tamper-proof so that it would be a hassle to detach.

Has anyone seen a product that would work for this solution?

3
  • 2
    Duct tape, perhaps? XD Sep 22, 2011 at 21:41
  • 2
    May I ask why the USB port needs to be out in the open and not concealed?
    – digitxp
    Sep 23, 2011 at 2:50
  • 4
    How about a post-it saying "I licked this"
    – dpatchery
    Sep 23, 2011 at 19:25

6 Answers 6

18

enter image description here

There are internal USB ports, get something like an internal USB adapter and remove it from the bracket or use an internal USB expansion module. Either mount the USB adaptor internally, or permanently fix it to a USB extension cable (cable tied to the inside of the case), and route it through a suitable office. If a headset dies, you're just out a usb extension cable and the dead headset

1
14

Have you tried superglue?

enter image description here

Heck, there are even ways to remove superglue: How to Remove Super Glue

1
  • Glue mold to the USB connector, make it look so disgusting that no one would want to touch it let along steal it...
    – Silverfire
    Sep 23, 2011 at 2:50
11

How about the NZXT Bunker Secure USB 2.0 Drive Bay? $24.99

http://www.legitreviews.com/article/1537/3/

enter image description here

The above image doesn't look like this would do anything for you, but the below image reveals how this could be helpful.

enter image description here

5

Although I like the superglue answer I can just imagine the IT guys pain when he needs to replace a broken headset.

I'd suggest a couple different things. One is an all in one type of case like Dell sells with the small form factor OptiPlex workstations. You can plug the device into the back and then put on the cover which can be secured.

The other option is to get a small lockable box with holes in each end. The holes would actually be slots so that when the lid is opened the wire can be pulled out (up). Attach the box to the desk and run a USB extension cable from the workstation to the box. Plug the headset into the extension cable and then close and lock the box.

1

Perhaps Conducting Glue

picture of wire glue

2
  • 1
    How would this work? Wouldn't it effectively cross the USB leads?
    – Chad Levy
    Sep 23, 2011 at 7:30
  • You would only glue the outer shell, which is connected to ground.
    – drxzcl
    Sep 23, 2011 at 9:08
-1

I still think the best idea is to have a USB cable extension run into a small lock box, like a hand gun lock-box, and keep the USB drive inside that. Someone would have to grind a 5mm hole at the edge of door for the USB extention cable to fit through. Most hand-gun boxes can be mounted securely to a desk so that's why I'd look for one of those. I doubt any office supply company will have a solution. Encryption of the drive alone won't work because if it's stolen the criminal won't get the data, but neither will you unless you backup constantly. I guess both a lock-box and encryption would be ideal.

2
  • 1
    This was more or less suggested by @waterwizard11 in 2011.
    – Ramhound
    Apr 13, 2016 at 16:56
  • The OP is asking about a USB microphone. Have the microphone inside a locked box pretty much ensures the microphone will not work as intended.
    – DavidPostill
    Apr 13, 2016 at 17:09

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy