Questions tagged [tomato]
Tomato is an alternative firmware for routers using Broadcom Chipsets.
192
questions
1
vote
1
answer
453
views
DHCP forwarding in FreshTomato
I have a wireless router that has a DHCP server (let's call it R1) and I connected another wireless router [linksys E2500 V3] (let's call it R2) to it using a LAN cable. R2 has a FreshTomato installed ...
- 99
0
votes
0
answers
28
views
OpenVPN tomato router with MFA or Google authenticate?
To access the tomato VPN router, the client must use a username, password, and then there is a certificate on the client computer as well. Technically this is a two factor authentication - password ...
- 11
3
votes
1
answer
159
views
AdvancedTomato can ping but cannot browse
Just moved and switched from comcast internet at my old place to verizon fios and tried to hook up my router (Netgear R6300v2 with Advanced Tomato firmware) to the ONT. I found I was able to ping but ...
- 33
0
votes
2
answers
131
views
Wireless bridge interferes with host wifi
I have an ASUS RT-AC68U with the Tomato USB firmware and I want to extend the existing wifi coverage (a LTE modem with router) for better reception in the rest of the house. Having the same subnet or ...
- 1,158
0
votes
1
answer
76
views
Home network cable differences
I'm trying to extend my home network to a second building close to my house. I've run a cat6 cable from my router (Google Wifi) to the second building, and when I jack it into my laptop everything ...
- 361
0
votes
0
answers
446
views
Why can't I ping an interface on another VLAN?
I have Netgear R7000 set up with FreshTomato, configured to act as a wireless AP. It has two bridges, feeding two virtual access points (SSIDs). The IP of one bridge is 192.168.3.2, and the other is ...
- 241
0
votes
0
answers
441
views
What subnet/netmask for OpenVPN server config on Tomato router?
I am setting up my Freshtomato router as OpenVPN server. The IP range of my router is 192.168.x.x/24.
However, In the OpenVPN server configuration on this router the subnet/netmask is pre-set to 10.6....
- 1
0
votes
2
answers
3k
views
DHCP Lease time renewal with ISP
Recently my ISP had a major outage and since they came back up I have been having issues with DHCP leases. I am currently using a DLink router with FreshTomato and there were no such issues before ...
- 3
1
vote
1
answer
2k
views
Weird ISP setup: Static ip behind carrier-grade NAT
I'm new to "ISP level" networking so this question might be a bit naive.
I've been having weird network issues in linux machines. As a debug/learning initiative, I decided to try and replace my ISP ...
3
votes
1
answer
4k
views
What Fresh Tomato settings to use to connect to modem with ip 192.168.1.1?
you’re my last straw. I bought a netgear nighthawk r7000 router and it worked fine out of the box (the genie switches to 10.0.0.1 because of an ip conflict with my modem). I flashed the firmware to ...
- 31
1
vote
0
answers
242
views
USB Hard Drive Mounted On Tomato Router Does Not Return HD Space Remaining or Number Of Files
Devices:
Netgear R7000 with Shibby Tomato Firmware 1.28.0000 -132 K26ARM USB AIO-64K
WD MyBook 6TB USB Hard Drive mounted as 'fuseblk' device on my router.
Multiple LAN Windows 10 Computers on a ...
- 49
1
vote
1
answer
570
views
iptables help - How to route guest network through wan firewall/port forwarding rules?
I have my network segmented into 2 parts:
Private Network - only trusted personal devices connected (wired & wireless), webserver, etc. and has outbound internet access. Also allowed access to * ...
- 111
0
votes
0
answers
112
views
Tomato Router: Configure LAN4 to obtain IP from ISP
I would like to achieve a configuration of my network where a server/PC/set-top-box connected to LAN4 port obtain IP from ISP, and it is visible on ISP's network. Thank you for any suggestions.
I ...
1
vote
3
answers
2k
views
Wifi is working, but can't connect to the Internet
I have a Linksys E1200 v2. I just flashed it with DD-WRT. Wifi is working properly and the signal is pretty strong. However, it won't connect to the Internet so it must be misconfigured. Is there an ...
- 622
0
votes
0
answers
66
views
Can access my DNS host from external network, but not within LAN
Basically, as in title.
This is on Advanced Tomato firmware.
NAT Loopback is configured. Currently as "Fowrward only" (there is a port forwarding rule as well). However, was trying to put "All" and ...
- 101
2
votes
1
answer
658
views
Tomato OpenVPN Client forwarding setup
I am using a VPN solely to get a dedicated/static IP (because my home network has a dynamic IP because its cable). I dont care about hiding my identity etc. I have the VPN set up on my router running ...
- 333
0
votes
1
answer
132
views
Additional "internal" access point with own DHCP
I am building myself a home automation system which will have some networked devices that connect to wifi and a few that connect via a cable. But I want those devices to be somewhat separate from my ...
- 101
0
votes
0
answers
1k
views
No Internet on Advanced Tomato router - Please advise
I got a new R7000 router, it worked fine on stock netgear firmware. I decided to flash it with advanced tomato 3.5-140.
Flashed and installed fine, I followed all the instructions.
However I can't ...
- 1
0
votes
1
answer
198
views
Use Tomato router as ethernet hub?
I'm running tomato 1.28 on my N600 netgear router, and I have the following situation:
I have an ethernet cord coming directly from a normal router (I'll call it router1), that I would like to use to ...
- 1,468
2
votes
0
answers
2k
views
Cannot flash a Netgear R8000 router with Tomato or DD-WRT firmware,
I purchased a new Netgear R8000 but cannot flash it with Tomato (Shibby or Advanced) or DD-WRT (Kong).
Any time I try to use the initial image I receive an error message stating that the firmware is ...
- 121
0
votes
0
answers
425
views
Cannot get port forwarding to work with Advanced Tomato
I'm trying to forward port 80 on my wan to one of my local computers for testing a web service. But I cannot get it to work and I don't really know where to start.
I did set up TCP port 80 to my ...
- 189
1
vote
1
answer
2k
views
OpenVPN clients have no connectivity over IPv6
I'm trying to add IPv6 tunnel support to a OpenVPN server (i.e. clients can access the IPv6 internet through VPN).
The router that runs OpenVPN (Netgear WNDR4500v1 running Tomato v1.28-140) has IPv6 ...
- 11
0
votes
0
answers
10k
views
Setup Tomato router as wireless repeater
I've setup DD-WRT routers before as wireless repeaters (link), but now I need to do the same but on a Tomato router, and apparently there's some difference in the terminology and the actual setup. ...
- 599
1
vote
1
answer
47
views
Will I need to re-authenticate all devices if I install AdvancedTomato on router and replace DD-WRT?
I am in a bit of a pickle. I would like to install AdvancedTomato over my existing DD-WRT router firmware, but I am afraid I will have to re-authenticate all devices previously connected to DD-WRT. I ...
- 113
2
votes
0
answers
812
views
Tomato Firmware producing high cpu load average (but low cpu usage)
I using an Asus RT-N18U router with the "Advanced Tomato" firmware with shibby's firmware under the hood.
I recognized a constant cpu load average of 2.00, but at the same time a low cpu usage.
"top" ...
- 121
1
vote
0
answers
1k
views
Advanced Tomato (Shibby) adblock whitelist doesn't work
I'm using Advanced Tomato (ver. 3.5-140), which is based on Shibby Tomato, on my Linksys E4200 router. The adblock function works, but the whitelist doesn't. When I add an url to the whitelist and ...
- 599
3
votes
0
answers
343
views
Bypass OpenVPN Tunnel for Specific Devices (IPs) on Tomato Router Setup
My setup is pretty straight forward.
ISP Modem - 192.168.1.1
|
Router - 10.0.0.1
/ | \
Devices
I've setup OpenVPN on the router so that all trafic is tunnelled over VPN. I'd like for certain ...
- 151
0
votes
1
answer
707
views
PPPoE Authentication Issues
So I have a R7000 running Advanced Tomato connected to a Technicolor TG589vac setup in bridge mode. Connecting directly to the technicolor I can do the PPPoE connection and have connectivity since It'...
- 333
0
votes
2
answers
1k
views
How can I access WWW from behind a LAN to WAN router cascade?
I am trying to set up a LAN to WAN router cascade using ethernet cable between a Belcom (Router 1) and a Linksys WRT54G running Tomato 1.28 (router 2). I am wanting to do this to improve parental ...
3
votes
1
answer
2k
views
Tunnel ports, thru VPS running OpenVPN, into my home network via Tomato Router
Long-story-short, my ISP has me double-NAT'ed = I can't open ANY ports.
My router is running Tomato firmware, and I have its OpenVPN client linked to a VPS running OpenVPN. I can divert my home ...
- 31
0
votes
0
answers
370
views
How to make traffic from internal IP skip VPN on tomato router?
On my Tomato router, in the VPN Client section under Advanced -> Custom Configuration, I need a command to cause all traffic from a local ip to skip the VPN. route my.static.local.ip 255.255.255....
- 260
1
vote
0
answers
3k
views
how does specifying mssfix for openvpn enable use of netflix?
The AirVPN forums contain this bit of advice for those trying to use Netflix with the VPN on a tomato router:
For whoever has run into trouble as not being able to use Netflix when the VPN is ...
- 260
4
votes
2
answers
2k
views
Exclude external IP from OpenVPN in tomato router
I have all traffic going through a VPN in my tomato router. I’d like to exclude my gaming server’s address from the VPN. How do I exclude that one specific external IP address from the VPN in the ...
- 260
2
votes
1
answer
15k
views
Tomato router: Bridge to Ethernet LAN, Devices access via Wireless
The tomato v1.28 instructions on learntomato.com most commonly describe the situation in which you have a wired device (such XBox) that you want to get onto your Wifi network, so you set up your Wifi ...
- 376
0
votes
1
answer
642
views
Tomato, Transmission, OpenVPN and Port Forwarding
My network configuration:
I run transmission on my Netgear R7000 router, it is running a fork (v2017.2) of [Tomato shibby by Kille72][1].
My router is not a gateway, it is set up as an access point ...
- 11
3
votes
1
answer
8k
views
My router false positively detects DNS-rebind attack
I have a router running the latest version of Advanced Tomato. Attempting to access a server on my home network (the same network as the router in question), by using my domain name (as opposed to my ...
- 31
0
votes
1
answer
2k
views
does AdvancedTomato Web Monitor 'Monitor Web Usage' also log HTTPS traffic?
I enabled this
Here some example logs:
zcat domain-201.....log.tar.gz
(..)
2017-05-03 00:19:29 192.168.1.23 update.appwork.org
2017-05-03 05:49:17 192.168.1.23 img.youtube.com
2017-05-03 17:39:...
- 820
0
votes
1
answer
904
views
Redirecting subnet traffic to a different gateway
I have a Debian Jessie box at 192.168.1.5 connected to the router (at 192.168.1.1) running an OpenVPN client (it's actually a Pi using this setup. The only part different is that the Pi's eth0 IP is ...
- 6,649
1
vote
0
answers
106
views
Access shared folder from behind Tomato VPN
This is my setup:
(192.168.1.254)Modem->(192.168.1.1)Tomato(via cabel)->(192.168.1.148)PC(Shared folders).
I was able to setup vpn for 10.8.0.0 and with 255.255.255.0, but only problem was, that my ...
- 111
4
votes
1
answer
1k
views
Advanced Tomato: 'Recent Web Searches' log always empty
The Recent Web Searches never worked. I tried with several different search engines (StartPage, DDG, Google, Yahoo) and never logs something.
I would like to enable that.
The Recently Visited Web ...
- 820
0
votes
1
answer
7k
views
Internet not working on Tomato Router
I just bought a brand new Netgear R7000 and flashed it with tomato. Its connected to my isp router (according to my isp is not possible to connect it directly to the modem) The flashing process was ok ...
0
votes
0
answers
850
views
Allow traffic from VPN Server clients to server restricted to VPN traffic on Tomato
I currently have Tomato running on my ASUS-Dark-Knight router. I also have the VPN server feature running which allows me to connect via OpenVPN to the router.
On the flip side, the VPN client ...
- 101
1
vote
1
answer
176
views
howto increase the range of WLAN - it must be a software issue - with stock firmware it was better
I own a Netgear R7000 router. After installing Advanced Tomato firmware, the range of WLAN decreased. Upstairs there is weak connectivity.
Do I have some sort of misconfiguration?
- 820
0
votes
1
answer
437
views
MultiWAN has slow failover
I have the latest Tomato Firmware using the MAX option.
I have the device configured for failover to the 2nd WAN if the main internet connection for WAN 1 goes down.
The issue I have is that WAN 1 ...
- 3,996
1
vote
1
answer
7k
views
Using ARP protocol with OpenVPN routed (TUN) tunnel
I've configured network shown in the following diagram:
ROT1 is Tomato-based router. It has BR0 bridged network interface for all the clients within internal network with subnet 192.168.1.0/24. One ...
1
vote
1
answer
1k
views
hotplug script in Tomato Shibby
I use Advanced Tomato on my Asus RT-AC68R/U. This is Shibby Tomato with some GUI modification only. I want to connect via USB measuring unit and create for it dedicated, unique device. At this moment,...
- 209
0
votes
1
answer
188
views
Is the WRT54G limited at ~20 Mbps on the switch <-> uplink traffic?
I have an old WRT54G which I wanted to reuse. The uplink is 100/100 Mbps but I only get about 20-30 Mbps between a wired device (laptop, RPi) connected to a switch port and Internet (when testing on ...
- 2,714
1
vote
3
answers
4k
views
Is there a custom firmware that will disable reset button/return to factory defaults for an Asus AC RT-56U?
I've been searching for information on the individual sites (DD-WRT, Open Wrt, Tomato, etc.), and finding nothing. One forum (not in DD-WRT site) indicated that DD-WRT does have a switch in its GUI ...
- 41
0
votes
2
answers
5k
views
Tomato router with separate DHCP server
I currently have a Netgear R7000 (running Tomato) acting as my main router (DHCP and DNS) and access point. Because of how my house is laid out, the modem and router are apart from each other (...
- 284
1
vote
1
answer
2k
views
Bandwidth limiter in Tomato (by Shibby) does not work
My device is Linksys E1200V2 and it previously ran tomato-E1200v2-NVRAM64K-1.28.RT-N5x-MIPSR2-137-Max but the bandwidth limiter won’t work.
So I Googled around and found a couple threads that said ...
- 319